Unpack the MultiPASS C5451 Carefully remove all items fromthe box.Remove these items from the documentation package:this Quick Start Guide, the MultiPASS C545 Installer CDpacket, MultiPASS C545 User's Manual, Registration card,and Warranty card.Remove these hardware items from the top tray:1Remove all pieces of shipping tape.Remove all pieces of shipping tape from the outside ofthe printer. Be sure to remove the tape from the back ofthe printer also.Remove the protective plastic piece from the sheet feeder.2MULTI-PURPOSE TRAY( FEEDER)AUTOMATICDOCUMENTFEEDER(ADF)Open the document tray.3Remove the protective sheet covering theoperation panel.Note that tape may not be in the exact locations shown.Open the operation panel.4Use both hands to grip the operation panel, andgently pull it toward you until it opens partially.Remove the soft styrofoam sheet from the unit'sAutomatic Document Feeder (ADF).PROTECTIVEPLASTICLift out the MultiPASS unit from the bottom.InkCartridgeBCl-21Made inJapanBlackSENDING DOCUMENTSUPPORTTELEPHONELINE POWERCORDBC-21e COLORBJ CARTRIDGEEXTRA BCI-21BLACK BJ TANKSB-21 BJ CARTRIDGESTORAGE BOXImportant! Save the box and shipping materials.You may need them later if you have to transportthe MultiPASS. Press the operation panel closed until it clicksinto place.Open the printer cover.5Check for any tape or shipping material insidethe unit and remove it.MULTI-PURPOSE TRAY(SHEET FEEDER) –holds paper forprinting or receiving faxesAUTOMATIC DOCUMENT FEEDER (ADF) –holds documents to befaxed, copied or scannedPRINTERCOVERCautionThe MultiPASS is equipped with a 3-prong,grounding-type plug. This plug will only fitinto a grounding-type outlet. This is a safetyfeature. Do not defeat the safety purpose ofthis plug. Make sure the socket-outlet islocated near the MultiPASS and is easilyaccessible.CANON/MPC545 Q.S.G: Pages 2 & 3 - File: 545QS2-3.epsWendi Swanlund Correx> August 19 '99PAGE 2 (BACKS COVER/1) PAGE 3 (BACKS 6)USB-TO-PARALLELCABLESet Up the MultiPASS2Attach the sending document support.Fit the tabs on the sendingdocument support into theslots above the ADF.Make sure thesupport curvestoward the backof the unit.1Connect the phone line.2Connect the USB—to—Parallel cableand power cord.3Make sure the computer is turned off.Connect the USB—to—Parallel cable to theMultiPASS and to yourcomputer.Place the main unit of the MultiPASS on a level surface with plenty of room to work.LIf you have only one telephone line and plan to use theMultiPASS for receiving both faxes and voice calls, youmust attach a telephone and/or answering machine tothe unit.Power Cord(to outlet)USB—to—Parallel Cable(to computer)Connect the power cord to the MultiPASS and toa wall outlet. The MultiPASS has no power switch.The power is on as long as the system is plugged in.ADFJacks onMultiPASSThe MultiPASS unit has three telephone jacks (locatedon the left side of the unit) that will accept standardline connections.LUse the bottom jack to connect the walljack to the MultiPASS with the suppliedline cord (unless connected with Caller ID).The other two jacks are pass-through portsto connect other devices to the MultiPASSand your telephone service. Select from theoptions in the diagram below to configureyour telephone device to work inconjunction with your MultiPASS.MultiPASS OnlyRecommended Device Connections Receive ModesFax Onlyor DRPDWall JackMultiPASS and Telephone Fax/Tel, DRPD,or ManualWall JackMultiPASS and Answering Machine Ans.MachineWall JackTelephoneAnsweringMachineMultiPASS, Answering Machine and Telephone Ans.MachineWall Jack AnsweringMachine TelephoneMultiPASS and PC Modem Fax Onlyor DRPDWall JackPCMultiPASS, PC Modem and TelephoneWall Jack PCTelephoneMultiPASS, PC Modem andAnswering MachineWall JackPCTelephoneAnsweringMachineMultiPASS, PC Modem, AnsweringMachine and TelephoneWall JackPCIf you use Caller ID with any of theseconfigurations, place the Caller ID devicebetween the MultiPASS and the wall jack.