Canon VIXIA HF G30 Quick Manual

Also see for VIXIA HF G30: Manual Instruction manual Connection guide Connection guide Manual

Contents

2Important Usage InstructionsImportant Usage InstructionsWARNINGTO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.COPYRIGHT WARNING:Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be contrary to copyrightlaws.The Mains plug is used as the disconnect device. The Mains plug shall remain readily operable to disconnect the plug in case of anaccident.CAUTION:• Danger of explosion if the wrong type of batteries are attached. Use only the same type of batteries.• Do not expose batteries or product to excessive heat such as the inside of a car under direct sunlight, fire, etc.FCC/IC NOTICEHD Camcorder, VIXIA HF G30 systemsThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmfulinterference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Note: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications shouldbe made, you could be required to stop operation of the equipment.Model ID0025 (including WLAN Module Model RF400, FCC ID: AZD400)This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this devicemay not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of thedevice.This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is noproof, however, that these low power wireless devices are absolutely safe. Low power wireless devices emit low levels of radio frequencyenergy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure oflow-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have notfound any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not beenconfirmed by additional research. This model has been tested and found to comply with FCC/IC radiation exposure limits set forth for anuncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radiofrequency (RF) Exposure rules.Compliance with FCC requirement 15.407(c)Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, andfinally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RFtransmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packetsis being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit oroperational failure.Frequecncy Tolerance: 25 ppmCanon U.S.A., Inc.One Canon Park, Melville, NY 11747, USATel No. 1-800-OK-CANON (1-800-652-2666)COPY