4down arrow keys to scroll through the top-level categories. Theseare listed in Appendix A and will be indicated on the ScrollingMarquee by the LED next to each mode listed on the face of thedisplay.When a specific mode or sub-mode is located, push the ENTERkey to enter the mode. Depending on the mode, there may beadditional tiers. Continue to use the up and down keys and theENTER keys until the desired display item is found. At any time,the user can move back a mode level by pressing the ESCAPE key.Once an item has been selected the display will flash showing theitem, followed by the item value and then followed by the itemunits (if any).Items in the Configuration and Service Test modes are passwordprotected. The display will flash PASS and WORD when required.Use the ENTER and arrow keys to enter the four digits of thepassword. The default password is 1111.Pressing the ESCAPE and ENTER keys simultaneously will scrollan expanded text description across the display indicating the fullmeaning of each display point. Pressing the ESCAPE and ENTERkeys when the display is blank (MODE LED level) will return thedisplay to its default menu of rotating AUTO VIEW display items.In addition, the password will need to be entered again beforechanges can be made.Changing item values or testing outputs is accomplished in thesame manner. Locate and display the desired item. If the display isin rotating auto-view, press the ENTER key to stop the display atthe desired item. Press the ENTER key again so that the item valueflashes. Use the arrow keys to change the value of state of an itemand press the ENTER key to accept it. Press the ESCAPE key andthe item, value or units display will resume. Repeat the process asrequired for other items.There are some points that can be forced from the ScrollingMarquee or the Navigator. If the user needs to force a variable,follow the same process as when editing a configuration parameter.A forced variable, regardless where the force has come from willbe displayed with a blinking “.” on a Scrolling Marquee and ablinking “f” on a Navigator following its value. For example, ifeconomizer commanded position (EC.CP) is forced, the Navigatordisplay shows “80f”, where the “f” is blinking to signify a force onthe point. The Scrolling Marquee display shows “80.” Where the“.” is blinking to signify a force on the point. Remove the force byselecting the point that is forced with the key ENTER and thenpressing the up and down arrow keys simultaneously.Depending on the unit model, factory-installed options andfield-installed accessories, some of the items in the various Modecategories may not apply.System Pilott and Touch Pilot DevicesThe System Pilot device (33PILOT--01) and Touch Pilot device(33CNTPILOT) can be used as CCN communicationuser--interfaces. These devices can be put on the CCN bus andaddressed to communicate with any other device on the network.Unlike the Scrolling Marquee and Navigator, these pilots read the48/50PD’s CCN tables and the units CCN points can be monitored,forced, or configured.IMPORTANT: Multiple zoning application is NOTrecommended at this time with the PD products.Additionally, the System Pilot device can serve as a wall--mountedtemperature sensor for space temperature measurement. Theoccupant can use the System Pilot device to change set points. Asecurity feature is provided to limit access of features forunauthorized users. See Fig. 3 for System Pilot device details.CCN Tables and DisplayIn addition to the unit--mounted Scrolling Marquee display, theuser can also access the same information through the CCN tablesby using the Service tool or other CCN programs/devices. Thevariable names used for the CCN tables and the Scrolling Marqueemenus may be different and more items may be displayed in theCCN tables. Details on the CCN tables are included with the localdisplay menus in Appendix A. Appendix A is structured towardsthe organization of the local display (Scrolling Marquee) menus.Because of the variety of CCN programs and devices, the CCNtables, sub--tables, and points are referenced within thatorganization.Table 2 — Scrolling Marquee Mode and Menu Display StructureRUNSTATUSSERVICETEST TEMPERATURES PRESSURES SETPOINTS INPUTS OUTPUTS CONFIGURATION TIMECLOCKOPERATINGMODESALARMSAuto ViewofRun Status(VIEW)↓SoftwareVersionNumbers(VERS)↓ControlModes(MODE)↓CoolingStatus(COOL)↓HeatingStatus(HEAT)↓EconomizerStatus(ECON)↓ComponentRun Hours(HRS)↓ComponentStarts(STRT)Service TestMode(TEST)↓Test IndependentOutputs(INDP)↓Test Fans(FANS)↓Test Cooling(COOL)↓Test Heating(HEAT)AirTemperatures(AIR.T)↓RefrigerantTemperatures(REF.T)GeneralInputs(GEN.I)↓CurrentSensor Inputs(CS.IN)↓Air QualityInputs(AIR.Q)FanOutputs(FANS)↓CoolOutputs(COOL)↓HeatOutputs(HEAT)↓EconomizerOutputs(ECON)↓AlarmRelay(ALRM)DisplayConfiguration(DISP)↓UnitConfiguration(UNIT)↓CoolingConfiguration(COOL)↓HeatingConfiguration(HEAT)↓EconomizerConfiguration(ECON)↓Air QualityCfg.(AIR.Q)↓Alarm RelayConfig.(ALM.O)↓PIDConfiguration(PID)↓SensorCalibration(TRIM)↓CCNConfiguration(CCN)Time of Day(TIME)↓Month, DateDay andYear(DATE)↓DaylightSavingsTime(DST)↓Local TimeSchedule(SCH.L)↓LocalHolidaySchedules(HOL.L)ControlModes(MODE)↓Cool ModeDiagnostic(COOL)↓Heat ModeDiagnostic(HEAT)↓EconomizerDiagnostic(ECON)↓DemandListing(DMD.L)Reset AllCurrentAlarms(R.CURR)↓ResetAlarmHistory(R.HIST)↓CurrentlyActiveAlarms(CURR)↓AlarmHIstory(HIST)48/50PD