Carrier 58CVA Installation, Start-up, Operating And Service And Maintenance Instructions

Carrier 58CVA Installation, Start-up, Operating And Service And Maintenance Instructions Manual pdf 5 page image

5AAB[736.9][736.9]2929Ø7/8Ø7/8[22.2][22.2]ACCESSORYACCESSORY5 15/165 15/16[150.7][150.7]28.3928.39[721.2][721.2]Ø7/8Ø7/8[22.2][22.2]ACCESSORYACCESSORY14 7/814 7/8[337.3][337.3](BOTH SIDES)(BOTH SIDES)Ø7/8Ø7/8[22.2][22.2]ACCESSORYACCESSORYØ7/8Ø7/8[22.2][22.2]ACCESSORYACCESSORYØ1 3/4Ø1 3/4[44.5][44.5]GAS ENTRYGAS ENTRYØ1/2Ø1/2[12.7][12.7]THERMOSTAT WIRE ENTRYTHERMOSTAT WIRE ENTRY22 1/1622 1/16[560][560]SIDE INLETSIDE INLET(BOTH SIDES)(BOTH SIDES)11 7/1611 7/16[290.7][290.7]9 11/169 11/16[245.4][245.4][197.8][197.8]7 13/167 13/16Ø7/8Ø7/8[22.2][22.2]J.BOX PROVISIONJ.BOX PROVISIONØ7/8Ø7/8[22.2][22.2]JUNCTION BOXJUNCTION BOXLOCATIONLOCATIONØ1 3/4Ø1 3/4[44.5][44.5]GAS ENTRYGAS ENTRY1 15/161 15/16[49.2][49.2]1[25.4][25.4]1 1/41 1/4[31.8][31.8]29 9/1629 9/16[750.7][750.7]1 15/161 15/16[49.2][49.2]5 5/85 5/8[143.3][143.3]5 7/165 7/16[138.5][138.5]6 13/166 13/16[172.3][172.3]Ø1/2Ø1/2[12.7][12.7]THERMOSTAT WIRE ENTRYTHERMOSTAT WIRE ENTRY1919[481.7][481.7]OUTLETOUTLETD21.621.6[549.5][549.5]BOTTOM INLETBOTTOM INLETC33 1/433 1/4[843.9][843.9]9 9/169 9/16[243.3][243.3]3/43/4[19.1][19.1]5 7/85 7/8[148.5][148.5]3 7/163 7/16[86.8][86.8]9 7/89 7/8[250.7][250.7]27 3/427 3/4[704.7][704.7]2 5/162 5/16[59][59]FRONT OF CASINGFRONT OF CASINGTOP OF CASINGTOP OF CASING4 13/164 13/16[122.2][122.2]27 3/427 3/4[704.7][704.7]5 7/85 7/8[148.5][148.5]8 5/88 5/8[219][219]5 1/25 1/2[140.3][140.3]8 7/168 7/16[213.5][213.5]FRONT OF CASINGFRONT OF CASINGTOP OF CASINGTOP OF CASING6.16.1[155.7][155.7]2 1/162 1/16[51.6][51.6]5.15.1[130.5][130.5]1.71.7[43.5][43.5]Ø7/8Ø7/8[22.2][22.2]ACCESSORY (2)ACCESSORY (2)AIR FLOWAIR FLOWAIR FLOWAIR FLOWBOTTOM RETURNBOTTOM RETURNWIDTHWIDTHAIR FLOWAIR FLOWKNOCK OUTS FORKNOCK OUTS FORVENTING(5VENTING(5PLACES)PLACES)A10290NOTES:1. Two additional 7/8 ---in. (22 mm) diameter holes are located in the top plate.2. Minimum return ---air openings at furnace, based on metal duct. If flex duct is used, see flex duct manufacturer’s recommendations for equivalent diameters.a. For 800 CFM---16 ---in. (406 mm) round or 14 1/2 x 12 ---in. (368 x 305 mm) rectangle.b. For 1200 CFM---20 ---in. (508 mm) round or 14 1/2 x 19 1/2 ---in. (368 x 495 mm) rectangle.c. For 1600 CFM---22 ---in. (559 mm) round or 14 1/2 x 22 1/16 ---in. (368 x 560mm) rectangle.d. For airflow requirements above 1800 CFM, see Air Delivery table in Product Data literature for specific use of single side inlets. The use of both side inlets,a combination of 1 side and the bottom, or the bottom only will ensure adequate return air openings for airflow requirements above 1800 CFM.Fig. 3 -- Dimensional DrawingTable 1 – Dimensions -- In. (mm)FURNACE SIZEACABINETWIDTHBOUTLETWIDTHCTOP ANDBOTTOM FLUECOLLARDBOTTOMINLET WIDTHVENTCONNECTIONSIZESHIP WT.LB (KG)ACCESSORYFILTER MEDIACABINET SIZE070 ---12/036070 14 ---3/16 (360) 12 ---9/16 (319) 9 ---5/16 (237) 12 ---11/16 (322) 4 (102) 115 (52) 16 (406)090 ---16/048090 17 ---1/2 (445) 15 ---7/8 (403) 11 ---9/16 (294) 16 (406) 4 (102) 130 (59) 16 (406)110 ---20/060110 21 (533) 19 ---3/8 (492) 13 ---5/16 (338) 19 ---1/2 (495) 4 (102) 155 (70) 20 (508)135 ---22/066135 24 ---1/2 (622) 22 ---7/8 (581) 15 ---1/16 (383) 23 (584) 4 (102)* 166 (75) 24 (610)155 ---22/066155 24 ---1/2 (622) 22 ---7/8 (581) 15 ---1/16 (383) 23 (584) 4 (102)* 175 (79) 24 (610)*135 and 155 size furnaces require a 5 or 6 ---in. (127 or 152 mm) vent. Use a vent adapter between furnace and vent stack. See Installation Instructions forcomplete installation requirements.4. If you touch ungrounded objects (and recharge your bodywith static electricity), firmly touch a clean, unpaintedmetal surface of the furnace again before touching controlor wires.5. Use this procedure for installed and uninstalled (ungroun-ded) furnaces.6. Before removing a new control from its container, dis-charge your body’s electrostatic charge to ground to pro-tect the control from damage. If the control is to be in-stalled in a furnace, follow items 1 through 4 beforebringing the control or yourself in contact with the fur-nace. Put all used and new controls into containers beforetouching ungrounded objects.7. An ESD service kit (available from commercial sources)may also be used to prevent ESD damage.LOCATIONGENERALThis multipoise furnace is shipped in packaged configuration.Some assembly and modifications are required when used in anyof the four applications shown in Fig. 4.NOTE: For high--altitude installations, the high--altitudeconversion kit MUST be installed at or above 5500 ft. (1676 M)above sea level. Obtain high--altitude conversion kit from yourarea authorized distributor.58CV