Carrier INDUCED COMBUSTION 58YAV Service And Maintenance Instructions

Also see for INDUCED COMBUSTION 58YAV: Service and maintenance instructions User's information manual Users information manual for the operation and maintenance

Contents

Carrier INDUCED COMBUSTION 58YAV Service And Maintenance Instructions Manual pdf 8 page image

Fig. 8—Service LabelA99233SERVICEGRYWComHUMTESTLEDLED CODE STATUS24V1112131421222324313334*9 86 53 2 147COMPONENT TESTNO PREVIOUS CODE - Stored status codes are erased when power(115VAC or 24VAC) to control is interrupted or 48 hours after each fault is cleared.BLOWER ON AFTER POWER UP (115VAC or 24 VAC) - Blower runs for 90seconds, if unit is powered up during a call for heat (R-W closed).LIMIT OR FLAME ROLL-OUT SWITCH LOCKOUT - Control will auto reset afterthree hours. Reset switch or replace fuse link. Refer to #33.IGNITION LOCKOUT - Control will auto-reset after three hours. Refer to #34.GAS HEATING LOCKOUT - Control will NOT auto reset.Check for: - Mis-wired gas valve -Defective control (Valve relay)ABNORMAL FLAME-PROVING SIGNAL - Flame is proved while gas valve isde-energized. Inducer will run until fault is cleared.Check for: - Leaky gas valve - Stuck-open gas valvePRESSURE SWITCH DID NOT OPEN - Check for:- Obstructed pressure tubing. - Pressure switch stuck closed.SECONDARY VOLTAGE FUSE IS OPENCheck for: - Short circuit in secondary voltage (24VAC) wiring.PRESSURE, DRAFT SAFEGUARD, AUX-LIMIT SWITCH (when used*) OR BLOCKEDVENT SWITCH (when used) DID NOT CLOSE OR REOPENED(DOWNFLOW ONLY*) If open longer than five minutes, inducer shuts off for 15minutes before retry. Check for: - Proper vent sizing- Low inducer voltage (115VAC) - Defective inducer motor- Defective Blower motor or capacitor - Restricted vent- Defective pressure switch - Excessive wind- Inadequate combustion air supply- Disconnected or obstructed pressure tubingIf it opens after trial for ignition period, blower will come on for 90 secondrecycle delay.LIMIT OR FLAME ROLL-OUT SWITCH IS OPEN - If open longer than threeminutes, code changes to #13. Flame roll-out switch requires manual reset.Check for: - Defective blower motor or capacitor.- Dirty filter or restricted duct system.- Loose blower wheel.- Defective switch or connections.- Inadequate combustion air supply (Flame Roll-out Switch or fuse link open).- Open Flame Roll-out Switch, or fuse link. Manual reset or replace.IGNITION PROVING FAILURE - Control will try three more times beforelockout #14 occurs. If flame signal lost after trial for ignition period, blowerwill come on for 90 second recycle delay. Check for:- Oxide buildup on flame sensor (clean with fine steel wool).- Proper flame sense microamps (.5 microamps D.C. min., 4.0 - 6.0 nominal).- Gas valve defective or gas valve turned off.- Defective Hot Surface Ignitor - Manual valve shut-off.- Low inlet gas pressure. - Control ground continuity- Green wire MUST be connected to furnace sheet metal.- Inadequate flame carryover or rough ignition.- Flame sensor must be ungrounded.To initiate the component test sequence, shut OFF the room thermostat ordisconnect the "R" thermostat lead. Briefly short the TEST terminal to the "Com24V" terminal. Status LED will flash code and then turn ON the inducer motor.The inducer motor will run for the entire component test. The hot surface ignitor,blower motor-heat speed, and blower motor-cool speed will be turned ON for10-15 seconds each. Gas Valve and Humidifier will not be turned on.If status code recall is needed, do not remove power or blower door. Briefly remove and thenreconnect one main limit wire to display stored status code.CONTINUOUS OFF - Check for 115VAC at L1 and L2, and 24VAC at SEC-1 andSEC-2.CONTINUOUS ON - Control has 24VAC power.RAPID FLASHING - Line voltage (115VAC) polarity reversed. If twinned, referto twinning kit instructions.EACH OF THE FOLLOWING STATUS CODES IS A TWO DIGIT NUMBER WITH THE FIRSTDIGIT DETERMINED BY THE NUMBER OF SHORT FLASHES AND THE SECOND DIGIT BYTHE NUMBER OF LONG FLASHES.320615-102 REV. K (LIT)8