Cavius 9001 Manual
Model no.: 9001PLEASE READ THE USER GUIDE C A R E -F U L LY B E F O R E U S E A N D RETAIN FORFUTURE USE!GENERAL DESCRIPTIONThe Smart Remote is designed to alert with arapid flashing warning light when alarming and toremotely control the CAVIUS Wireless Alarm Fam-ily. The torch function can be used to find escaperoutes at night.SAFETY INSTRUCTIONSBatteries are to be handled with care and batterypowered devices should be kept out of reach of chil-dren. Do not try to recharge or burn the batteries.TECHNICAL INFORMATIONThe Smart Remote can be used with the alarms fromthe CAVIUS Wireless Alarm Family: Smoke, Heat,Flood and Mains Power alarms. The maximumnumber of alarms that can be interlinked with is 32.The minimum range is 100m in open field. RF condi-tions also depend on the house layout and materials.You should always test it after installation and afterchanging batteries.Diameter: 27mm. Length: 140mm.The Smart Remote is powered by 3 replaceable AAAbatteries.1. HOW TO CONNECT TO THE WIRELESSALARM FAMILY:Open the battery compartment by pressing thesnap. Insert the batteries in the battery compart-ment respecting polarities.Slide the learn switch to the “Learn mode” posi-tion. The Smart Remote will go into Learn mode.All alarms that need to be connected to theSmart Remote in the house should be put into“Learn mode” by sliding the switch of each deviceon the “Learn mode” position.The flashlight will light up to indicate that “Learnmode” has been selected.Please note: Do not take out the batteries during“Learn mode” as this will interrupt the learn process.Press and hold the test button on an alarm, ofyour own choice, until it beeps and the LEDflashes. This alarm will become the master andwill start sending out a specific house code tothe other alarms.As the other alarms receive the specific housecode, they will also start flashing their red LED’s.When the red LED light flashes on all alarms,they are connected and MUST BE SWITCHEDOUT OF ‘LEARN MODE’ and installed.Label the original “Learn” alarm in order to easilyadd new CAVIUS Wireless Family alarms to thesystem.2. INSTALLATION:The body of the Smart Remote has a built-in magnet,so it can be installed on a metal plate mounted onthe wall, or on a fridge or other metal surfaces.The accompanying metal plate can be installed bythe double sided tape or the enclosed screw set.The end cap has a hole in which a lanyard canbe added so the remote can hang from a hooketc.3. TEST FUNCTION:After installation, and at least once per quarter,test all your alarms by pressing the test button onthe remote to ensure they are operating correctlyand are within range of each other.It is recommended to check visually every weekif the LED flashes correctly on the alarm (every48sec.).Hold the red end button for two swipes of alarmsuntil the remote stops flashing, sounding and vi-brating.The remote is now transmitting a test signal toyour alarms. During the test, the Smart Remote willflash and sound.If the Smart Remote is receiving a test signal fromanother device, it will also flash and sound toindicate that it is part of the group. Indication canbe stopped by pressing the end button.Please note: To ensure an optimal operation in nor-mal conditions, test function sends out a reducedpower RF signal.4. ALARM MODE:When one of the connected alarms is going intoalarm and sending out the RF alarm signal, theSmart Remote’s flashlight will start flashing rapidly(stroboscope).The Smart remote has a built in vibrator andsounder which will follow the sound pattern ofthe originating alarm. During the alarm, both thesounder and vibrator will be activated.The torch can be switched from stroboscopic flash-ing to constant on by pressing the side button.Please note: Flashlight will flash at 2 Hertz (2times each second) to avoid photo sensitiveepilepsy to be triggered.The CAVIUS Wireless Family has two differentalarm signals:Alarm signal 1 (--- --- ---) is life threateningalarms, like a smoke alarm.Alarm signal 2 (- - -) is a non life threateningalarm, like a flooding alarm:Smoke alarm signal: --- --- ---Heat alarm signal: --- --- ---Flood alarm signal: - - -Please note that only the originating alarm’s LEDwill flash, so it can be identified.UKEnd button for test/hushMagnet holderLearn mode switchFlashlightEnd cap for battery accessSide button for flashlightNormal Mode Learn Mode |
Related manuals for Cavius 9001
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine