Dacor Discovery DYRP48D-C-S Installation Instructions Manual

Also see for Discovery DYRP36DS: Planning guide Instruction manual Installation instructions Use and care manual Installation instructions

Contents

Dacor Discovery DYRP48D-C-S Installation Instructions Manual Manual pdf 9 page image

7Preparing for InstallationWARNING• If the gas or electric service provided does not meet theproduct specifications, do not proceed with the installation.Call the dealer, the gas supplier or a licensed electrician.• Before installing the range, you must locate and secure theanti-tip bracket to the floor.IMPORTANT: Within the Commonwealth of Massachusetts, thisappliance must be installed by a licensed plumber or gas fitter.Unpacking the RangeUnpack the parts box and verify that all required componentshave been provided. If any item is missing or damaged, pleasecontact your dealer immediately. Do not install a damaged orincomplete appliance.Installation InstructionsParts List- 3 Grates- 8 Standard burner caps(4 brass, 4 porcelain)*- 4 Standard burner rings- 4 SimmerSear burner caps(2 brass, 2 porcelain)*- 2 SimmerSear burner rings- 2 SimmerSear burner heads- 2 GlideRack™ oven racks- 1 Standard rack- 2 GlideRack™ 18” wide ovenracks (DYRP48D only)- 1 18” wide standard oven rack(DYRP48DS only)- 6 Knobs (4 Standard,2 MAX GRIDDLE)- Anti-tip bracket with screwsand anchors- Meat probe- Griddle- Wok ring- Stainless steel cleaner- Literature kit- Broiler pan/grill*The range is supplied with two different types of burner caps(brass and porcelain) to suit the customer’s preference.Installing a Downdraft Vent (Optional)Install the downdraft vent before installing the range. See theinstallation instructions included with the downdraft vent.IMPORTANT: The downdraft vent attaches to the narrow backportion of the cutout. It is self-supporting in the cutout and doesnot actually attach to the range itself.Installing a Backguard (Optional)Install the backguard before making the range gas and electricalconnections. Install it according the installation instructionsincluded with the backguard kit.Approved backguard kits:Model DescriptionAPB36D3 3 inch high backguard for range model DYRP36DSAPB36D9 9 inch high backguard for range model DYRP36DSAPB48D3 3 inch high backguard for range model DYRP48DSAPB48D9 9 inch high backguard for range model DYRP48DSInstall the Anti-Tip Bracket and FootLocate the anti-tip bracket included in the parts box.There are two ways to mount the anti-tip bracket:• Floor mounting (preferred method)• Wall mounting (alternate method). Use this method if floormounting is not suitable. If the front panel of range is furtherthan 26 1/2” (67.3 cm) from the back wall or if the flooring istoo thick (see Installing the Anti-Tip Bracket on the Wall),the wall mounting method may not be used and the floormounting method must be suitable.Installing the Anti-Tip Bracket on the FloorWARNINGTo perform its intended function, the anti-tip bracket must beattached as instructed to the concrete slab or wood sub-floorbelow any floor coverings (including cement board) on top. Donot attach the anti-tip bracket directly to floor coverings such asceramic/asphalt tile or linoleum.Four (4) plastic anchors are provided along with three sizes (4each) of #8 or #12 Phillips head screws for attaching the anti-tip bracket to the floor. Use both the anchors and four (4) of thescrews when attaching the bracket to a concrete sub-floor. Do notuse the provided anchors when attaching to a wood sub-floor.continued...Sub-floorScrews attached tosub-floor below floorcoveringAnti-tipbracketFloorcoveringConcrete anchors shown, donot use for wood sub-floor