Daewoo DF-7150D User Manual

Contents

Daewoo DF-7150D User Manual Manual pdf 21 page image

PLAYBACK3938Press the VCR button to set the remote control to operate the VCR deck.Turn the TV on and select the video input source connected to the DVD Recorder+VCR.Audio system: Turn the audio system on and select the input source connected to the DVD Recorder+VCR.Before You Begin1 Insert a prerecorded video cassette.If the DVD Recorder+VCR is powered off, it will power on automatically.Make sure the TIMER indicator on the front panel display is not lit. If it is, press [POWER] once.If a tape without a safety tab is inserted, the DVD Recorder+VCR will start playback automatically.2 Press [PLAY/PAUSE].The PLAY icon appears on the TV screen. It is not necessary to select the tape speed (SP, LP) for playback.It will be automatically selected by the DVD Recorder+VCR.3 Press [STOP] to stop playback.The STOP icon appears on the TV screen. If the tape reaches the end before [STOP] is pressed, the DVDRecorder+VCR will automatically stop, rewind, and eject the tape.Playing a VHS TapeAuto TrackingThe automatic tracking function adjusts the picture to remove snow or streaks. It works in the following cases:• When a tape is played for the first time.• When the tape speed (SP, LP) changes.• When streaks or snow appear because of scratches on the tape.Manual TrackingIf noise appears on the screen during playback, press the [TRACKING +/-] buttons on the remote control untilthe noise on the screen is reduced.• In case of vertical jitter, adjust these controls very carefully.• Tracking is automatically reset to normal when the tape is ejected or the power cord is unplugged for morethan 3 seconds.Tracking ControlVCR PlaybackVCR Playback• If the DVD Recorder+VCR is powered on by inserting a video cassette, playback will not start automatically.Notes on special playback featuresHorizontal lines (noise bars) will appear on the TV screen. This is normal.The audio is automatically muted during special playback modes, so there is no sound during search, slow motion, etc.During high-speed picture search, a short time is needed to stabilize tape speed when re-entering Play mode. Slightinterference may be observed during this time.Fast Forward/BackwardThis function lets you visually search forward and backward for a desired scene on your tape.1 Press [REW] or [FF] during playback.Search mode will be activated.If the DVD Recorder+VCR is left in Search mode for more than 3 minutes, the DVD Recorder+VCR willautomatically resume Play mode to protect the tape and video heads.2 To return to normal playback, press [PLAY].Still Picture1 Press [PLAY/PAUSE] during playback.A still picture appears on the TV screen.If a still picture vibrates vertically, stabilize it by using the [TRACKING +/-] buttons on the remote control.If the DVD Recorder+VCR is left in Still mode for more than 5 minutes, the DVD Recorder+VCR willautomatically enter Stop mode to protect the tape and video heads.2 To return to normal playback, press [PLAY].Slow Motion1 Press [SLOW+] for Slow Motion playback.2 Press [SLOW+] and [SLOW-] repeatedly to adjust the Slow Motion playback speed.Counter Memory FunctionThis is useful if there is a section of tape you want to view immediately after recording or if you want to returnto the same point several times.1 Begin recording or playing a tape.2 At the point you want to locate later, reset the real-time counter to 0:00:00 by pressing [CLEAR]. Continueto play or record.3 Press [STOP] when recording or playback finishes.4 You can make the tape automatically stop when the counter returns to about ‘0:00:00‘ by setting thecounter to ‘0:00:00‘ in the ‘Go-To Search‘ function under ‘Setup’ ➝ ‘Preferences’ ➝ ‘VCR’; see page 31.Special Playback FeaturesVCR Playback