Manuals database logo
manualsdatabase
Your AI-powered manual search engine

Daikin Altherma EHVH04SU18CB6W Installation Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Contents
  1. installation manual
  2. Table Of Contents
  3. Indoor unit
  4. Preparing electrical wiring
  5. Mounting the indoor unit
  6. Connecting the water piping
  7. To connect the pressure relief valve to the drain
  8. To connect the main power supply
  9. To connect the backup heater power supply
  10. To connect the user interface
  11. To connect the electrical meters
  12. To connect the safety thermostat (normal closed contact)
  13. Overview: Configuration
  14. Basic configuration
  15. Quick wizard: Options
  16. Quick wizard: Capacities (energy metering)
  17. Domestic hot water control
  18. Menu structure: Overview installer settings
  19. Checklist before commissioning
  20. To perform an air purge
  21. Maintenance safety precautions
  22. To drain the domestic hot water tank
  23. Components and dimensions: Indoor unit
  24. Piping diagram: Indoor unit
  25. Wiring diagram: Indoor unit
  26. Technical specifications: Indoor unit
Daikin Altherma EHVH04SU18CB6W Installation Manual Manual pdf 14 page image
4 InstallationInstallation manual14EHVH04+08SU18CB6W + EHVH08~16SU26CB6WDaikin Altherma – Low temperature split4P449980-1B – 2016.114.5.13 To connect the safety thermostat (normalclosed contact)1 Connect the safety thermostat (normal closed) cable to theappropriate terminals as shown in the illustration below.3 4X5M2 Fix the cable with cable ties to the cable tie mountings.INFORMATIONAfter it is installed, do NOT forget to configure the safetythermostat. Without configuration, the indoor unit willignore the safety thermostat contact.INFORMATIONThe preferential kWh rate power supply contact isconnected to the same terminals (X5M/3+4) as the safetythermostat. It is only possible for the system to haveEITHER preferential kWh rate power supply OR a safetythermostat.4.5.14 To connect the booster heater powersupplyWARNINGThe booster heater MUST have a dedicated power supplyand MUST be protected by the safety devices required bythe applicable legislation.CAUTIONTo guarantee the unit is completely earthed, alwaysconnect the booster heater power supply and the earthcable.INFORMATIONThe non-self-resetting thermal cut-out of the booster heateris set below 89°C.Make sure that the power supply is in accordance with the boosterheater capacity, as listed in the table below.Booster heatercapacityPower supply Maximum runningcurrent2.4 kW 1~ 230 V 11 A1 Connect the booster heater power supply cable to theappropriate terminals as shown in the illustration below.F2BL NL N2 Fix the cable with cable ties to the cable tie mountings.4.6 Finishing the indoor unitinstallation4.6.1 To fix the user interface cover to theindoor unit1 Make sure that the front panel is removed from the indoor unit.See "4.1.1 To open the indoor unit" on page 5.2 Plug the user interface cover into the hinges.3 Mount the front panel to the indoor unit.4.6.2 To close the indoor unit1 Close the switch box cover.2 Reinstall the top plate.3 Reinstall the front panel.NOTICEWhen closing the indoor unit cover, make sure that thetightening torque does NOT exceed 4.1 N•m.
/ 32
This manual is suitable for:
EHVH04SU18CB6WEHVH08SU18CB6WEHVH08SU26CB6WEHVH11SU26CB6WEHVH16SU26CB6W
Manuals database logo
manualsdatabase
Your AI-powered manual search engine