Daikin FAQ71BVV1B Techical Data

Also see for FAQ100BVV1B: Service manual Operation manual Operation manual Installation manual Operation manual

Contents

Daikin FAQ71BVV1B Techical Data Manual pdf 11 page image

ï Indoor Units ï R-410A ï FAQ-BVV1B8ï Split Sky Air ï Indoor Units108 Wiring diagram8 - 1 Wiring diagram3D043881AFAQ71BA1P Printed circuit boardHAP Light emitting diode (service monitor green)M1S Motor (swing flap)M1F Motor (indoor fan)R1T Thermistor (air)R2T Thermistor (coil)SS1 Selector switch (emergency)X1M Terminal blockX2M Terminal blockPower supply? Signal receiver circuit. Signal transmission circuitInfrared remote controlReceiver / display unitA2P Printed circuit boardA3P Printed circuit boardBS1 Push button (on/off)H1P Light emitting diode (on-red)H2P Light emitting diode (timer-green)H3P Light emitting diode (filter sign-red)H4P Light emitting diode (defrost-orange)SS1 Selector switch (main/sub)SS2 Selector switch (wireless address set)Connector for optional partsX15A Connector (float switch)X35A Connector (group control adapter)Wired remote controlR1T Thermistor (air)SS1 Selector switch (main/sub)To outdoorunitNote) 4In case of simultaneousoperation system.To outdoor unitNotes1. D : Terminal, F : Connector, : Field wiring2. In case using central remote control, connect it to theunit in accordance with the attached instructionmanual.3. Remote control model varies according to thecombination system, confirm technical materials andcatalogs, etc. before connecting.4. X24A is connected when the infrared remote controlkit is being used.5. Shows short circuit connector6. Symbols show as follows Red:red, Blk:black, Ylw:yellow,Org:orange, Gry:gray, Prp:purple, Blu:blue7. Confirm the method of setting the selector switch (SS1,SS2) by installation manual and engeneering materials,etc.Receiver / display unit (attached to infrared remote control)Note) 4Indoor unit(master)Indoor unit(slave)Remote controlNorm. Emerg.Note) 2Transmission wiringcentral remote controlWired remote controlControl boxSIDE FRONTON/OFF input from outside3D044228AFAQ100BA1P Printed circuit boardA2P Printed circuit board(Transformer) 230V/16V)C1R Capacitor (M1F)HAP Light emitting diode (service monitor green)KAR Magnetic relay (M1S)KPR Magnetic relay (M1P)M1F Motor (indoor fan)M1S Motor (swing flap)Q1M Thermo switch (M1F embedded)R1T Thermistor (air)R2T Thermistor (coil)S1Q Limit switch (swing flap)SS1 Selector switch (emergency)V1TR Phase control circuitX1M Terminal blockX2M Terminal block? Signal receiver circuit. Signal transmission circuitWired remote controlR1T Thermistor (air)SS1 Selector switch (main/sub)Infrared remote controlReceiver / display unitA3P Printed circuit boardA4P Printed circuit boardBS1 Push button (on/off)H1P Light emitting diode (on-red)H2P Light emitting diode (timer-green)H3P Light emitting diode (filter sign-red)H4P Light emitting diode (defrost-orange)SS1 Selector switch (main/sub)SS2 Selector switch (wireless address set)Connector for optional partsX15A Connector (float switch)X25A Connector (drain pump)X35A Connector (group control adapter)X16AX61A Connector (interface adapter for sky air series)To outdoorunitNote) 4Wired remotecontrolControl boxIn case of simultaneousoperation system.To outdoor unitNotes1. D : Terminal F, : Connector2. : Field wiring3. In case using central remote control, connect it tothe unit in accordance with the attachedinstruction manual.4. X24A is connected when the infrared remotecontrol kit is being used.5. Remote control model varies according to thecombination system, confirm technical materialsand catalogs, etc. before connecting.6. Symbols show as follows Red:red, Blk:black,Ylw:yellow, Org:orange, Gry:gray, Prp:purple,Blu:blue7. Confirm the method of setting the selectorswitch (SS1, SS2) by installation manual andengeneering materials, etc.8. x15A, x25A are connected when the drain up kitis being used. Connect it to the kit in accordancewith the attached installation manual.Receiver / display unitNote) 4Indoor unit(master)Indoor unit(slave)Infrared remotecontrolEmerg.Norm.Note) 8