Daikin FNA25A2VEB Installer's Reference Manual

Also see for FNA25A2VEB: Installation manual Operation manual Installer's reference guide

Contents

2 About the documentationInstaller reference guide7FNA25~60A2VEBSplit system air conditioners4P482940-1 – 2017.06WARNING▪ ONLY use copper wires.▪ Make sure the field wiring complies with the applicablelegislation.▪ All field wiring must be performed in accordance withthe wiring diagram supplied with the product.▪ NEVER squeeze bundled cables and make sure theydo not come in contact with the piping and sharpedges. Make sure no external pressure is applied to theterminal connections.▪ Make sure to install earth wiring. Do NOT earth the unitto a utility pipe, surge absorber, or telephone earth.Incomplete earth may cause electrical shock.▪ Make sure to use a dedicated power circuit. NEVERuse a power supply shared by another appliance.▪ Make sure to install the required fuses or circuitbreakers.▪ Make sure to install an earth leakage protector. Failureto do so may cause electric shock or fire.▪ When installing the earth leakage protector, make sureit is compatible with the inverter (resistant to highfrequency electric noise) to avoid unnecessary openingof the earth leakage protector.NOTICEPrecautions when laying power wiring:▪ Do not connect wiring of different thicknesses to thepower terminal block (slack in the power wiring maycause abnormal heat).▪ When connecting wiring which is the same thickness,do as shown in the figure below.▪ For wiring, use the designated power wire and connectfirmly, then secure to prevent outside pressure beingexerted on the terminal board.▪ Use an appropriate screwdriver for tightening theterminal screws. A screwdriver with a small head willdamage the head and make proper tighteningimpossible.▪ Over-tightening the terminal screws may break them.WARNING▪ After finishing the electrical work, confirm that eachelectrical component and terminal inside the electricalcomponents box is connected securely.▪ Make sure all covers are closed before starting up theunit.NOTICEOnly applicable if the power supply is three‑phase, and thecompressor has an ON/OFF starting method.If there exists the possibility of reversed phase after amomentary black out and the power goes on and off whilethe product is operating, attach a reversed phaseprotection circuit locally. Running the product in reversedphase can break the compressor and other parts.2 About the documentation2.1 About this documentINFORMATIONMake sure that the user has the printed documentation andask him/her to keep it for future reference.Target audienceAuthorised installersINFORMATIONThis appliance is intended to be used by expert or trainedusers in shops, in light industry, and on farms, or forcommercial and household use by lay persons.Documentation setThis document is part of a documentation set. The complete setconsists of:▪ General safety precautions:▪ Safety instructions that you must read before installing▪ Format: Paper (in the box of the indoor unit)▪ Indoor unit installation manual:▪ Installation instructions▪ Format: Paper (in the box of the indoor unit)▪ Installer reference guide:▪ Preparation of the installation, good practices, reference data,…▪ Format: Digital files on http://www.daikineurope.com/support-and-manuals/product-information/Latest revisions of the supplied documentation may be available onthe regional Daikin website or via your dealer.The original documentation is written in English. All other languagesare translations.Technical engineering data▪ A subset of the latest technical data is available on the regionalDaikin website (publicly accessible).▪ The full set of latest technical data is available on the Daikinextranet (authentication required).3 About the box3.1 Overview: About the boxIt contains information about:▪ Unpacking and handling the units▪ Removing the accessories from the unitsKeep the following in mind:▪ At delivery, the unit must be checked for damage. Any damagemust be reported immediately to the carrier's claims agent.▪ Bring the packed unit as close as possible to its final installationposition to prevent damage during transport.▪ Prepare the path along which you want to bring the unit inside inadvance.