Daikin FTYN25DV3B Installation Manual

Also see for FTN25DAV3B: Operation manual Operation manual

Contents

Daikin FTYN25DV3B Installation Manual Manual pdf 4 page image

English 2Accessories– ,*1 The thermistor cable is attached to the indoor unit.Choosing a Site• Before choosing the installation site, obtain user approval.Installation Tips How to remove the front panel.• Hook fingers on the panel protrusions on the left and right of the main body, and open until the panel stops.• Slide the front panel sideways to disengage the rotating shaft.• Then pull the front panel toward you to remove it. How to attach the front panel.• Align the tabs of the front panel with the grooves, and push all the way in.• Then close slowly.• Push the center of the lower surface of the panel firmly to engage the tabs. How to remove the front grille.• Open the front panel.• Remove the screws (2 pcs) on the front grille.• Pull the lower part of the front grille toward you, then remove the front grille completely.(There are 2 hooks on the upper part.)If it is difficult to remove, open the front grille and raise the top grid, using a screwdriver,to unhook the hooks. How to attach the front grille.• Attach the front grille to the bottom frame, and lock the upper hooks (2points) securely.• Tighten the screws (2 pcs) on the front grille.• Attach the front panel and close the front panel. How to set the different addresses.• When two indoor units are installed in one room, the two wireless remote con-trollers can be set for different addresses. PCB in the indoor unit.• Remove the front panel.• Remove the electric parts box (1-screw).• Slide the metalic cover to remove it. (4-claws on the electric parts box)• Cut the jumper JA on PCB. Wireless remote controller.• Cut the jumper J4.Mounting plate 1 Remote controller holder 1 Thermistor cable (8m)*1 1Mounting plate fixing screwM4 × 25L 6 Fixing screw for remotecontroller holder M3 × 20L 2 Operation manual 1Titanium Apatite PhotocatalyticAir-Purifying Filter 2 AAA dry-cell batteries 2 Installation manual 1Wireless remote controller 1 Indoor unit fixing screwM4 × 12L 2 Drain plug(Heat pump-Models) 1The indoor unit should be sited in a place where:• the restrictions on installation specified in theindoor unit installation drawings are met,• both air intake and exhaust have clear paths met,• the unit is not in the path of direct sunlight,• the unit is away from the source of heat or steam,• there is no source of machine oil vapour (thismay shorten indoor unit life),• cool (heat) air is circulated throughout the room,• the unit is away from electronic ignition type flu-orescent lamps (inverter or rapid start type) asthey may shorten the remote control range,• the unit is at least 1 metre away from any televi-sion or radio set (unit may cause interferencewith the picture or sound).The outdoor unit should be sited in a place where:• the restrictions on installation specified in the outdoor unit installation diagram are met,• drain water causes no trouble or problem in particular,• both air intake and exhaust have clear paths of air (they should be free ofsnow in snowy districts),• the unit is in a clear path of air but not directly exposed to rain, strongwinds, or direct sunlight,• there is no fear of inflammable gas leakage,• the unit is no directly exposed to salt, sulfidized gases, or machine oilvapour (they may shorten outdoor unit life),• operation noise or hot air flow does not cause trouble to neighbours,• the unit is at least 3 metres away from any television or radio antenna.• Turn on all the fluorescent lamps in the room, if any, and find the site where remotecontroller signals are properly received by the indoor unit (within 7 metres).Indoor unit A L Outdoor unit MA E JB F KC G LD H MIndoor unit Outdoor unitWireless remote controllerFit the key into the slot.Filter guideScrewdriverUpper grilleRaise andremove HookScrewdriverUpper hookJ4 ADDRESSEXIST 1CUT 2J4CUT 2ADDRESS: JAEXIST 1JAJC C1C31J30JP11ADDRESSMetalliccoverClaws (4 point)ElectricpartsboxPCBWirelessremotecontroller