Daikin RXYSQ-P8Y1 Technical Data Manual

Daikin RXYSQ-P8Y1 Technical Data Manual Manual pdf 34 page image

• Outdoor Unit • VRVIII-S heat pump • RXYSQ-P8Y1111• VRV Systems • Outdoor Unit3211 Installation11 - 1 Service SpaceRXYSQ-P8Y13D045696D• Obstacle on both sides100 or more100 or more100 or more100 or more1000 or more 200 or more300 or more500 or less100 or more1000 or more1000 or more500 or less150 or more150 or more 150 or more500 or less1000 or more 200 or more300 or more1000 or more500 or more1000 or more1000 or more500 or less500 or more1000 or more1000 or more500 or less500or more 100 ormore300 ormore1000or more500 or less1000 or more250 or more300 or more1000 or more500or less500 or more 100 or more1500or more500 or less1000 or more1000or more500 or less1000 or more1500or moreAor more1000 or moreDrain pipingconstruction dimension Drain pipingconstruction dimension300or more1000or more200or more 2000or more 100or more1500or more600or more3000or moreRequired installation space(The unit of these values is ‘mm’)1. Where there is an obstacle on the suction side:(a) No obstacle above(1) Stand-alone installation• Obstacle on the suctionside only(b) Obstacle above, too(1) Stand-alone installationThe relations between H, A and L are follows:L AL H 0 < L 1/2 H 1001/2 H < L H 200H > L Set the stand as: L HClose the bottom of theinstallation frame to prevent thedischarged air from beingbypassed.(2) Series installationThe relations between H, A and L are as followsL AL H 0 < L 1/2 H 2501/2 H < L H 300H < L Set the stand as: L HRefer to the column of L H for AClose the bottom of theinstallation frame to prevent thedischarged air from beingbypassed.Only two units can be installed for this series.5. Multiple rows of series installation(on the rooftop, etc.)(a) One row of stand-aloneinstallation(b) Rows of series installation (2 or more)The relations between H, A and L are as followsL AL H 0 < L 1/2 H 2501/2 H < L H 300H < L Can not be installed(2) Series installation (2 or more)The relations between H, A and L are as followsL A0 < L 1/2 H 2501/2 H < L H 300(a) Obstacle above, too(1) Stand-alone installation(2) Series installation (2 or more)2. Where there is an obstacle on the discharge side:(a) No obstacle above(1) Stand-aloneinstallation(b) Obstacle above, too(1) Stand-alone installationThe relations between H, A and L are as followsL AL H 0 < L 1/2 H 7501/2 H < L H 1000H < L Set the stand as: L HClose the bottom of theinstallation frame to prevent thedischarged air from beingbypassed.(2) Series installation (2 or more)The relations between H, A and L are as follows:L AL H 0 < L 1/2 H 10001/2 H < L H 1250H < L Set the stand as: L HClose the bottom of theinstallation frame to prevent thedischarged air from beingbypassed.Only two units can be installed for thisseries3. Where there are obstacles on both suction anddischarge sides:Pattern 1Where the obstacle on the discharge side is higher than theunit:(There is no height limit for obstructions on the intake side)(a) No obstacle above(1) Stand-alone installationPattern 2Where the obstacle on the discharge side is lower than theunit:(There is no height limit for obstructions on the intake side)(a) No obstacle above(1) Stand-alone installation(2) Series installation (2 or more)(2) Series installation (2 or more)(2) Series installation (2 or more)• Obstacle on the suction side and both sides(b) Obstacle above, too(1) Stand-alone installation• Obstacle on the suctionside, too• Obstacle on the suctionside and both sides(2) Series installation (2 or more)• Obstacle on both sides4. Double-decker installation(a) Obstacle on the discharge sideclose the gap A (the gap betweenthe upper and lower outdoor units)to prevent the discharged air frombeing bypassed .Do not stack more than two units.(b) Obstacle on the suction side closethe gap A (the gap between theupper and lower outdoor units) toprevent the discharged air frombeing bypassed .Do not stack more than two units.L > HL > HL H