Danco 10561 Instructions Manual

Also see for 10561: Instructions

Danco 10561 Instructions Manual Manual pdf 1 page image

Dwco INSTRUCTIONS - UNIVERSAL TRIM KIT FOR MOEN* ADDITIONAL INFORMATIONTo properly installthis product, a 3-h inch round opening in the wall is requiredfor the offset portion of the faceplatetrim to recess in, or else it will protrude from the walBefore you beginFOR QUICK & EASY3D ASSEMBLY INSTRUCTIONSBILT Download the Apb'Store GooglePlayo FREEAppCorrect Valve Identification FigureBefore removing the old tub/shower faucet trim or handles, please determine the configuration of the valve bodyTo turn the water from OFFto ON, do you:1) ROTATEhandlerightto eft (counter-clockwise)f you ROTATEthe handlefrom right to leftyou haveValveTypeA (PosiTempe)2) PULL the handleIfyou PULLthe handleto turn the waterON,you haveValveTypeB (MoentroIS)Please Note:f you use a diverter, Fig. 1 shows with and without diverter applications.Metal lever handles do not work with valves that include diverter If diverter is used, you must use clear, plastic handleCheck screw hole pattern for Valve Type B. Mounting screws are located: at a 2 0'clock & 7 0'clock position or at a5 0'clock & 7 0'clock position Note which one is usedInstallation of Faceplate Figures 3, 4Slidetube (D) overvalvebody(TypeA)or (Type B)Note: Larger diameter tube (Dl) isused for Type A valves. Smaller diametertube (D2) is used for Type B valvesFIGURE 1VALVE APosi Temp'shown without diverterV- notchStemLorem ipsumTabsRemoval of Old Trim Figure 2VALVE TYPE aMoentrolshown with diverterStemDiverterFIGURE 2234.Shut off water supply to tub/showerfaucet This may require shutting off themain water supply to the house orfacility Once the water supply is shut off,turn on the faucet to allow the waterpressure to be released,then reclose faucetRemovethe handleindexbutton (A)fromthe old handle(Fig 2) Removehandlescrew (B) and handle (C).Remove faceplate screws (E) and oldfaceplate(F) Slideoff bodysleeve(D)Confirm correct valve selection afterremoving old trim (see Fig 1)A B cValve Type A Applications Figures 5, 6, 71 Slide stem washer (N) over valve stem (Fig 5)2. Insert bushing (0) into tubeFIGURE 5Preassembledtogether in package3. Ensurestop(P) is insertedinto Bushing(O)Note: This is a temperature limiting device Rotate the stop (P)clockwise and press in to place to limit hot water output(!) THISDOESNOTREDUCETHENEEDTOLOWERTHETEMPERATUREOF THE WATER HEATER TO PREVENT SCALDING.Determine handle type to be usedNote: Metal ever handles do not work with valves that include diverter.For Metal Lever Handle Figure 61 Locate metal handle adapter (Q) Place handleadapteroverstem,securein placeusingscrew(R),making sure orientation is downward2 Placemetal,leverhandle(S) over metalhandleadapter(Q)andsecureusinghex screw(T)from undersideof handlewithAllenWrench(K)For Clear Plastic Handle Figure 7FIGURE 62Locate clear plastic handle (U). Remove the handleindex button (X) Make sure plastic adapter (Z) isremoved from handle. Place handle over valve stem,pointeddownward Using1-1/4"screw (V)and ockwasher (W), secure in place.Presshandleindexbutton(X) into clearp astichandle02 (l)Tube(Small)12Tube GasketDiverter Foam GasketFIGURE 7xScrew 32 x 1 3/4Faceplate GasketMoentrol'shown without diverterStemzA1an Wrench23456Locate new faceplate (F) If va ve body includes diverter,removeO-ring(L) anddiverterplug (G)fromfaceplate(F)Remove paper backing from diverter foam gasket (M) andadhere to the back of the faceplate (F) around the diverter hole(K). If no diverteris used,leavediverterplug (G)in placeandproceedto Step3Select the correct faceplate insert (H) The insert with the argerinner diameter is for Type A valves; the insert with the smallerinner diameter is used for Type B valves Note the screwlocations for Type B valves and select the appropriate faceplateinsert Removethe paper backing from the appropriate tubegasket (I) and adhereto the back side of the appropriatefacep ate insert (H)Snapthefaceplateinsert(H)in to thefront of the faceplate(F)Press firmly to snap in placePlace the faceplate gasket (J) into the back of the faceplate (F)Slidethefaceplateassemblyoverthe tube(D), makesurethediverter hole (K) is located downward Pressthe faceplateassembly firmly against the wall. Secure the faceplate to thevalvebodyusingthe includedfaceplatescrews(E)B ValveTypeBApplicationsFigures8.9Determine handle type to be usedNote: Metal lever handles do not work with valvesthat include diverter.For Metal Lever Handle Fig. 8ValveType 8ValveType BINSTALLATION OF HANDLEGvxValveType ALFDiverterHoleo122.Slide stem washer (N) over valve stem Locatemetalhandleadapter(Y). Placehandleadapteroverstem,securein placeusingscrew (R),making sure orientation is downwardPlace metal lever hand e (S) over handleadapter(Y) Secure using hex screw (T) fromundersideof handlewithAllenWrench(K)For Clear Plastic Handle Figure 91 Slide stem washer (N) over stem Locate clear,plastichandle(U). If notalreadyinstalled,instalplasticadapter(Z) into clear,plastichandle.Note:Pressadapter(Z)firmly into handle(U)2.When ful y installed, adapter will be even withthe bottom of handle. Place handle assemblyover valve stem, pointed upward. Using 1-1/4"screw (V)and lockwasher(W), securein place.Presshandleindexbutton(X) into clearplastichandleFIGURE 3FIGURE 4FIGURE 8si/'iiFIGURE 9OzwQUANTITYD2ValveType ADiv rterHole0ITEMTube (Large)Tube Gasketo -RingStem WasherFacepateOScrew 1/2"screw #6-32 x 5/8"Lever HandleDiverterPlugoPlastic Hand eMetalHandleAdapterHI (l)Faceplatensert(Preassembledin Faceplate(F))H2Facepate nse•rlH3FaceplateInsertPlasticAdapter(preassembledin handle)PART#12oswz2BushingOlp partsPreassembledtogetherin packageScrew 24*1-1/4owLock WasherMetalHande AdapterHandle Index ButtonTube (Large)Tube (Small)Screw #8 32 x 1-3/4"FaceplateDiverter PlugFaceplate InsertFaceplate InsertFaceplate InsertTube GasketTube GasketFaceplate GasketAllen WrenchO-ringDiverter Foam GasketStem WasherBushingStopMetal Handle AdapterScrew #10-24 x 1/2"Lever HandleScrew #6 32 X 5/8"P astic HandleScrew #10-24 x 1-1/4"Lock WasherHandle Index ButtonMetal Handle AdapterP astic Adapter0 2018 Danco IncNing, TX 75062Made in China10001i / 10002i / 10561i EIS 04052018

/ 2

Related manuals for Danco 10561