Danfoss VLT 5000 Operating Instructions Manual

Also see for VLT 5000 FLUX: Service manual Operating instructions Operating instructions Operating instructions Operating instructions

Danfoss VLT 5000 Operating Instructions Manual Manual pdf 4 page image

VLT® 5000/ 5000 FLUX/ 6000 HVAC/8000 AQUA PROFIBUSIntroduction IntroductionCopyrights, Limitation of Liability and Revision RightsThis publication contains information proprietary toDanfoss A/S. By accepting and using this manual theuser agrees that the information contained herein willbe used solely for operating equipment of Danfoss A/Sor equipment from other vendors provided that suchequipment is intended for communication with Danfossequipment over a PROFIBUS serial communicationlink. This publication is protected under the Copyrightlaws of Denmark and most other countries.Danfoss A/S does not warrant that a software programproduced according to the guidelines provided inthis manual will function properly in every physical,hardware or software environment.Although Danfoss A/S has tested and reviewed thedocumentation within this manual, Danfoss A/S makesno warranty or representation, either express or implied,with respect to this documentation, including its quality,performance, or fitness for a particular purpose.In no event shall Danfoss A/S be liable for direct,indirect, special, incidental, or consequential damagesarising out of the use, or the inability to use informationcontained in this manual, even if advised of thepossibility of such damages. In particular, DanfossA/S is not responsible for any costs including but notlimited to those incurred as a result of lost profitsor revenue, loss or damage of equipment, lossof computer programs, loss of data, the costs tosubstitute these, or any claims by third parties.Danfoss A/S reserves the right to revise this publicationat any time and to make changes in its contentswithout prior notice or any obligation to notify previoususers of such revisions or changes.NB!:Note regarding Profibus FMSIf you want to run FMS you have topurchase as follows:For VLT 5000:175Z3722 (uncoated)175Z3723 (coated)For VLT 6000 HVAC:175Z4207 (uncoated)175Z4208 (coated)It is NOT possible to run FMS from a VLT 5000FLUX or a VLT 8000 AQUA.This manual does not deal with Profibus FMS,only with Profibus DP. However, in the eventthat the communication is to be built up throughProfibus FMS, you should request the descriptionMG.10.E3.yy "Profibus Product Manual" whichalso contains a description of the Profibus FMSfunctions of the Profibus option card. About this manualThis manual is intended as both an instruction manualand a reference guide. It only broaches the basics of thePROFIBUS DP protocol, and only when it is necessaryto provide a sufficient understanding of the PROFIDRIVEimplementation of the PROFIBUS profile for frequencyconverters (version 2, PNO) and of the PROFIBUSoption card for the series VLT 5000/VLT 5000 Flux/VLT6000 HVAC/VLT 8000 AQUA by DANFOSS.Unit Software versionFCD 300 Ver. 1.30FCM 300 -VLT 2800 Ver. 2.64VLT 5000 Ver. 3.62VLT 6000 HVAC Ver. 2.41VLT 8000 AQUA Ver. 1.12The above table shows from which software versionsProfibus DP V1 is supported. The software version canbe read-out in parameter 624 Software versions.This manual gives detailed information of the DP V0features supported, sufficient for most programmingand maintenance activities. The DP V1 howeveris briefly described. For programming purposesthe Profibus DP V1 Design Guide order numberMG.90.EX.YY (X is the version number, and YY thelanguage code) might be necessary.It is suggested that readers who are notcompletely familiar with PROFIBUS DP or theprofile for frequency converters review the relevantliterature on these subjects.MG.90.G1.02 - VLT is a registered Danfoss trademark 3