Datalogic Heron D130 Quick Reference Manual

Also see for Heron D130: Quick reference Quick reference guide

Contents

DEFAULT VALUES

Datalogic Heron D130 Quick Reference Manual Manual pdf 2 page image

DEFAULT VALUESUSB-KBD DEFAULT SETTINGSUSA keyboard, FIFO enabled, inter-character and inter-code delays disabled,control character emulation = ctrl+shift+key.DATA FORMAT : code identifier disabled, no field adjustment, code length nottransmitted, no header, terminator = ENTER, character replacement disabled.RS232 Standard DEFAULT SETTINGS9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking, delay disabled, rxtimeout 5 sec., ack/nack disabled, FIFO enabled, serial trigger lock disabled.DATA FORMAT : code identifier disabled, no field adjustment, code length nottransmitted, no header, terminator = CR-LF, character replacement disabled.WEDGE DEFAULT SETTINGSUSA keyboard, caps lock off, caps lock auto-recognition enabled, num lockunchanged, inter-character and inter-code delays disabled, control characteremulation = ctrl+shift+key.DATA FORMAT : code identifier disabled, no field adjustment, code length nottransmitted, no header, terminator = ENTER, character replacement disable.PEN DEFAULT SETTINGSinterpret mode, conversion to code 39 disabled, output level normal, idle levelnormal, minimum output pulse 600 μs, overflow medium, inter-block delay disabled.CODE SELECTIONEnabled codes• EAN 8/EAN 13 / UPC A/UPC E without ADD ONcheck digit transmitted, no conversions• Interleaved 2/5check digit control and transmission, variable length code; 4-99 characters• Standard Code 39no check digit control, variable length code; 1-99 characters• Code 128variable length code; 1-99 charactersDisabled codesEAN 128, ISBT128, Code 93, Codabar, pharmaceutical codes, MSI,Plessey, Telepen, Delta IBM, Code 11, Code 16K, Code 49, RSS CodesTECHNICAL FEATURESHeron™ D130Electrical FeaturesPower SupplyRS232 interface 5 Vdc ± 5%Consumption:MaximumOperatingSleep mode/USB Suspend180 mA @ 5 Vdc155 mA @ 5 Vdc<500 μA @ 5 VdcMax. Scan Rate 256 scans/secReading Indicators LED, Good Read Spot, BeeperOptical FeaturesSensor CCD solid state (2048 pixels)Illuminator LED arrayWavelength 630 ~ 670 nmMax. LED Output Power 0.31 mWLED Safety Class Class 1 EN 60825-1Reading Field 2 ~ 27 cm (20 mils)Max. Resolution 0.10 mm (4 mils)PCS (Datalogic Test Chart) min. 15%Environmental FeaturesWorking Temperature 0 °C to + 55 °C (+32° to +131 °F)Storage Temperature -20 °C to + 70 °C (-4° to +158 °F)Humidity 90% non condensingDrop Resistance IEC 68-2-32 Test ED1.8 m (5.9 ft)ESD Protection 16 KVProtection Class IP30Mechanical FeaturesWeight (without cable) about 160 g (5.6 oz)Cable Length 2 m (6 ft 6 in)RESTORE DEFAULTRESTORE DEFAULTÌ$+$*oÎTo change the defaults refer to the HHD II Software Configuration Manual, partnumber 90ACC1877, or to the Configuration program, both downloadable from thewebsite.INTERFACE SELECTIONSelect one of the interface codes according to your application.USB INTERFACE SELECTIONUSB-KBDÌ$+UA03$-:ÎUSB-KBD - ALT-modeÌ$+UA04$-@ÎUSB-COM *Ì$+UA02$-4ÎUSB-IBM-Hand HeldÌ$+UA01$-.Î* When configuring USB-COM, the relevant files and drivers must be installedfrom the USB Device Installation software, which can be downloaded from theweb site http://www.datalogic.com.PEN EMULATION INTERFACE SELECTIONPENÌ$+CP6$-BÎRS232 INTERFACE SELECTIONRS232 StandardÌ$+CP0$-$ÎNixdorf Mode AÌ$+CM2EC0$->ÎFujitsuÌ$+CM1$-ÈÎICL ModeÌ$+CM0$-ÃÎWEDGE INTERFACE SELECTIONWedge IBM AT or PS/2 PCsÌ$+CP500$-aÎPC NotebookÌ$+CP505$-ÈÎPC Notebook - ALT modeÌ$+CP508$-2ÎIBM AT - ALT modeÌ$+CP507$-+ÎMany other interfaces are supported and can be selected from the HHD IISoftware Configuration Manual available online at datalogic.com. Other supportedinterfaces:USB: USB-IBM-Table Top; USB-KBD-APPLEWEDGE: IBM XT; IBM SURE1; IBM Terminal 3153; IBM Terminals 31xx, 32xx,34xx, 37xx; Wyse Terminals ANSI – PC –ASCII – VT220 style Keyboards; DigitalTerminal VT2xx/VT3xx/VT4xx; APPLE ADB BusKEYBOARD NATIONALITYUSB-KBD and Wedge users should select one of the following wedge keyboardnationality codes according to your keyboard.BelgeÌ$+FJ7$-8ÎDeutschÌ$+FJ3$-$ÎEnglishÌ$+FJ4$-)ÎEspañolÌ$+FJ6$-3ÎFrançaisÌ$+FJ2$-ÊÎItalianoÌ$+FJ1$-ÅÎJapaneseÌ$+FJ8$-=ÎSvensktÌ$+FJ5$-.ÎUSA (Default)Ì$+FJ0$-|ÎDATA FORMAT TERMINATORSFor your convenience, some common Terminators are given below. For otherHeader/Terminator selections, Data Format and Advanced Data Formatparameters, see the HHD II Software Configuration Manual.CR-LFÌ$+EA120D0A$-ÃÎEnterÌ$+EA1183$-0ÎTabÌ$+EA1184$-8ÎNoneÌ$+EA10$-dÎOPERATING TESTRead the TEST code below.Code 128t e s tUSING HERON™ SERIES READERSHeron™ guns automatically scan barcodes at a distance. Simply aim and pull thetrigger. Code scanning is performed along the center of the light bar emitted fromthe reading window. This bar must cover the entire code.Successful scanning is obtained by tilting the scanner with respect to the barcodeto avoid direct reflections, which impair the reading performance, see the figureabove.Successful reading is signaled by an audible tone plus a good-read green spot.By correctly inserting the reader into the stand, it is immediately ready toautomatically read any code present in its reading area without pressing thetrigger. Furthermore, a green aiming light is continuously emitted to facilitate thepositioning of the barcode to be read, see the figure above.To guarantee single code reading, same code consecutive reading requires thecode to be removed from the reading area (no decoding) before the reader willaccept the same code.STAND INSTALLATIONThe stand can be mounted by using self-tapping screws, double sided adhesivestrips or rubber feet:A) mount the stand directly to the surface using theself-tapping screws;B) carefully clean the bottom surface of the stand and the table surface.Remove the protective plastic from one side of the adhesive strips and stickthem on the stand bottom. Then, remove the plastic from the other side ofthe strips and affix the stand to the table;C) carefully clean the bottom surface of the stand, remove the protective filmfrom the rubber feet and stick them in the corresponding housing on thebottom surface. It is also possible to fix an optional metal plate.INSERTION INTO STANDPair the reader to the stand paying attention to insert the handle into the stand clip(see figure above). Correct insertion will be signaled by a beep; then, the readerwill be ready to read barcodes.ABC

/ 2

Related manuals for Datalogic Heron D130