Datalogic IO-Link S5N-P Series Instruction Manual
This product is covered by one or more of the following patents.European Patent 851,211 B1; 1,111,690 B1; 1,148,346 B1; 1,209,487 B1.Italian Patent IT 1,321,772.S5N-Px SERIESINSTRUCTION MANUALInformation on IO-Link communication is available on the lastpage of this manual.CONTROLSOUTPUT LED (S5N-Px…B01/C01/T01)The yellow LED ON indicates that the NO output status is closed.STABILITY LED (S5N-Px…B01/C01)The green LED ON indicates that the received signal has a reservegreater than 30% compared to the output switching value.TRIMMER (S5N-Px…B01/C01/T01)The trimmer can be used to adjust sensitivity; the operating distanceincreases turning the trimmer clockwise.WARNING: The trimmer rotation is limited to 270° by a mechanical stop.Do not apply excessive torque when adjusting (max 40 Nmm).INSTALLATIONThe sensor can be fixed by means of the M18x1 threaded body througha 18mm hole, using the specific washer and the two CH.24 nutsenclosed (1.5Nm maximum tightening torque).Alternatively, the sensor can be mounted through the two housing’sholes using two screws (M3x22 or longer) and washer.Amongst the various possible solutions, we suggest to choose thecombination that offers the best visibility of the signalling LEDs and theeasiest access to the trimmer.Wide range of accessories available: 22mm nuts, h=8mm, (2Nmmaximum tightening torque) guarantee an improved torque and variousorientable fixing brackets ease the sensorpositioning (please refer to the accessorieslisted in the general catalogue).The operating distance is measured from thefront surface of the sensor lens.C models: To improve the detection, theobject has to be moved closer or further awayfrom the front surface of the sensor lens.In case of lateral translation, the object mustmove as indicated in the figure.CONNECTIONSThe connections are compliant to the EN 60947-5-2 standard.M12 CONNECTOR10 … 30 Vdc-+N.O. OUTPUT/IO-Link0 VN.C. OUTPUT 2314DIMENSIONS24N°.2 Ø3.84=2.5=4=3.82STABILITY LED1015M18x11.5143.5243.51.5442=3.814121014.5N°.2 Ø3.8TRIMMER1524441.512N°.2 Ø3.8TRIMMER39.5 15 M18x11014Ø22Ø2.2mm14=M18x16.2=Ø4252525RADIAL VERSIONFIBRE OPTIC VERSIONTRIMMEROUTPUT LEDSTABILITY LEDOUTPUT LEDOUTPUT LEDSTABILITY LEDOUTPUT LEDSTABILITY LEDwithout trimmerLXX1M O D E L Swith trimmerX1XAXIAL VERSIONwithout trimmerLXX1M O D E L Swith trimmerXX1CABLE VERSION=M12=M12=M126°14.5L 14.5L79434669423657422467433472.5 14.510TECHNICAL DATAS5N-PA AXIAL VERSION S5N-PR RADIAL VERSIONPower supply: 10 … 30 Vdc (limit values)Ripple: 2 Vpp max.Current consumption(output current excluded): 35 mA max.Outputs: NO and NC; PNP or NPN (short-circuit protection)Output current: 100 mA max.Output saturation voltage: 2 V max.Response time: 0.5 ms (2 ms mod.F01/G00)Switching frequency: 1KHz (250 Hz mod.F01/G00)Indicators: OUTPUT LED (YELLOW) excluding mod.G00STABILITY LED (GREEN) (mod.B01/C01/C21/E01/F01)POWER ON LED (GREEN) (mod.G00)Setting: sensitivity trimmer (mod.B01/C01/C21/E01/F01/T01)Operating temperature: -25 … 55 °CStorage temperature: -25 … 70 °CInsulating strength: 500 Vac 1 min., between electronics and housingInsulating resistance: >20 M 500 Vdc, between electronics and housingOperating distance (typical values): B01: 0.1…3.5 m on R2C01: 0…60 cmT01: 0.1…1 m on R2B01: 0.1…2 m on R2C01: 0…35 cmT01: 0.1…1 m on R2Emission type: red (630 nm) (mod. E01) / red (660 nm) (mod.B01/T01) /infrared (880nm) (mod. C01/C21/G00)Ambient light rejection: according to EN 60947-5-2Vibrations: 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6)Shock resistance: 11 ms (30 G) 6 shock for every axis (EN60068-2-27)Housing material: PBTLens material: PMMAMechanical protection: IP67Connections: M12 - 4 pole connectorWeight: 25 g. max. connector vers.AtEx 2014/34/EU: I I 3G EX nA II T6I I 3D EX tD A22 IP67 T85°CSETTINGSetting of S5N-Px…B01/T01Position the sensor and reflector on opposite sides.Turn the sensitivity trimmer to the maximum position.Moving the sensor both vertically and horizontally, determine the power on and offpoints of the yellow LED (OUT) and then mount the sensor in the middle of thepoints defined. Optimum operation is obtained when the green LED (mod.B01) isON and the yellow LED is OFF.B01 models: If necessary reduce sensitivity in order to detect verysmall targets. In order to improve alignment, repeat the proceduredetailed above whilst progressively reducing the sensitivity.T01 model: Turn the sensitivity trimmer counterclockwise until theyellow LED turns ON (pos.A). Turn slowly the trimmer again clockwise until theyellow LED turns OFF (Operating condition, pos.B).Setting of S5N-Px…C01Turn the sensitivity trimmer to minimum: the green LED is ON, the yellow LED isOFF. Position the target to detect in front of the sensor or of the fibre terminals.Turn the sensitivity trimmer clockwise until the yellow LED turns ON (Targetdetected state, pos.A).Remove the target, the yellow LED turns OFF.Turn the sensitivity trimmer clockwise until the yellow LED turns ON (Backgrounddetected state, pos.B).The trimmer reaches maximum if the background is not detected.Turn the trimmer to the intermediate position C, between the two positions A andB. The green LED must be ON.Datalogic S.r.l.Via S. Vitalino 13 - 40012 Calderara di Reno - ItalyTel: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.comHelpful links at www.datalogic.com: Contact Us, Terms and Conditions,Support.The warranty period for this product is 36 months. See General Terms andConditions of Sales for further details.For information about the disposal of Waste Electricaland Electronic Equipment (WEEE), please refer to thewebsite at www.datalogic.com.© 2007 - 2019 Datalogic S.p.A. and/or its affiliates ALL RIGHTSRESERVED Without limiting the rights under copyright, no part of thisdocumentation may be reproduced, stored in or introduced into a retrievalsystem, or transmitted in any form or by any means, or for any purpose,without the express written permission of Datalogic S.p.A. and/or itsaffiliates. Datalogic and the Datalogic logo are registered trademarks ofDatalogic S.p.A. in many countries, including the U.S.A. and the E.U. Allother trademarks and brands are property of their respective owners.Datalogic reserves the right to make modifications and improvementswithout prior notification.821006321 Rev. BMIN MAXABC |
Related manuals for Datalogic IO-Link S5N-P Series
Datalogic IO-Link S100 Series Instruction Manual
Datalogic S5N-PL Series Instruction Manual
Datalogic S5N-M Series Instruction Manual
Datalogic S5N-M Series Instruction Manual
Datalogic S5N-M PP Series Instruction Manual
Datalogic S5N-PA W Series Instruction Manual
Datalogic S5N-PA U Series Instruction Manual
Datalogic IO-Link S8 Instruction Manual
Datalogic S51-PA Series Instruction Manual
Datalogic S5N-Px-PP/NN Series Instruction Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine