Memor™ X3 Single Ethernet DockRead this manual carefully before performing any typeof connection through the Memor X3 Single EthernetDock.The user is responsible for any damages caused byincorrect use of the equipment or by inobservance of theindication supplied in this manual.NOTEDo not attempt to disassemble the Memor X3 SingleEthernet Dock, as it does not contain parts that can berepaired by the user. Any tampering will invalidate thewarranty.NOTEThe Memor X3 Single Ethernet Dock paired with one Memor X3 mobilecomputer builds a reading system for the collection, decoding andtransmission of barcoded data.The communication between the mobile computer and host PC throughthe Memor X3 Single Ethernet Dock may occur also by using the standardActiveSync® connection.Figure 1 – Memor X3 Single Ethernet DockA) LED IndicatorsB) Spare Battery SlotC) Mini USB ConnectorD) RS232 ConnectorE) Power JackF) Ethernet Port with LED indicatorsG) Switch Ethernet/USBThe Memor X3 Single Ethernet Dock is a serial communication adapterbetween the host computer and the Memor X3 mobile computer. Powersupply is required to be connected to the Dock only for ethernetcommunication.Since the Memor X3 Single Ethernet Dock also functions as a batterycharger, a power supply is required for battery recharging operations, bothfor the mobile computer and spare battery pack recharging. The sparebattery pack recharging slot can supply a 1100 mAh, a 1430 mAh, a 2000mAh and a 2300 mAh Battery pac.822001522 (Rev. A) Jan. 2018MOBILE COMPUTER INSERTION/ REMOVALBy inserting the Memor X3 into the Dock, data can be transmitted to thehost and its battery begins charging if the power supply is connected. Inaddition, a spare battery can be charged by inserting it into the slot at theback of the Memor X3 Single Ethernet Dock as shown in the followingfigure.Figure 2 – Memor X3 Single Ethernet Dock Charging andCommunicationLED INDICATORSThe LEDs positioned on the front part of the Memor X3 Ethernet Dock(see figure below) indicate the Dock and spare battery charger status:Figure 3 - LED IndicatorsFront LED indicatorsLED STATUSCharger Red Constant Spare battery charging*Green Constant Spare battery charge completedPower Green It is constant when the Dock is powered* During charging, the LED may turn off to indicate a temporarysuspension of charging.Ethernet Connector LED IndicatorsEthernetGreen LED(left)Solid Green Link establishedFlashing Green Link activityOff No link establishedEthernetYellow LED(right)Off 10 Mb connectionSolid Yellow 100 Mb connection (this model is notavailable)CONNECTIONSConnections should always be made with power OFF!CAUTIONUSB ConnectionThe Memor X3 Single Ethernet Dock can be connected to the host bymeans of any standard Mini USB cable.Once the host has been turned on, insert the Memor X3 mobilecomputer into the Dock.Figure 4 - USB ConnectionA) Host Computer C) Memor X3 Single Ethernet DockB) Std Mini USB (i.e.94A051016 CAB-421)D) Power Supply* (only necessaryfor battery charging)Be sure that the switch is in the “USB” position.During switch operation from USB position to Ethernetposition and vice versa the mobile computer must not beinserted in the Dock.NOTE* Recommended power supply: 94ACC1324 PG5-30P35 AC/DC POWERSUPPLY EU/USA PLUG.BCDF GEASpare BatteryCharger LEDPower LEDABCDSpare batteryCharge Slot withSpare BatteryInsertedData Transmission andMobile Computer BatteryCharging