Dell Latitude 13 Service Manual

Also see for Latitude 13: Quick start guide Setup and features information Quick start guide Quick start guide

Computrace®NOTE: The Activate and Disable options will permanently activate or disable the feature and no further changes will be allowed.CPU XD SupportAllows you to enable or disable the Execute Disable mode of the processor.Default setting: EnabledPerformanceOption DescriptionMulti Core Support Enables or disables multi-core support for the processor.Intel® SpeedStep™ Enables or disables the Intel SpeedStep feature.Power ManagementOption DescriptionWake on AC Allows you to enable or disable the computer from turning on automatically when an AC adapter is connected.Auto On TimeAllows you to set the time at which the computer must turn on automatically.You can set the of days, if any, when you would like the system to turn on automatically. The settings are Disabled, Everyday, orWeekdays.Default setting: OffUSB WakeSupportAllows you to enable or disable the ability of USB devices to wake the computer from Standby.This feature is only functional when the AC power adapter is connected. If the AC power adapter is removed during Standby, the BIOSwill remove power from all of the USB ports to conserve battery power.Wake onLAN/WLANAllows the computer to turn on by a special LAN signal or from Hibernate state when triggered by a special wireless LAN signal. Wake-upfrom the Standby state is unaffected by this setting and must be enabled in the operating system.l Disabled — Do not allow the system to power on when it receives a wake-up signal from the LAN or wireless LAN.l LAN Only — Allow the system to be powered on by special LAN signals.l WLAN Only — Allow the system to be powered on by special WLAN signals.l LAN or WLAN — Allow the system to be powered on by special LAN or wireless LAN signals.The factory default setting is Off.ExpressChargeAllows you to enable or disable the ExpressCharge feature.NOTE: ExpressCharge may not be available for all battries.Charger BehaviorAllows you to enable or disable the battery charger. If disabled, the battery will not lose power when the system is connected to an ACadapter but it will not charge either.Default setting: Charger EnabledPOST BehaviorOption DescriptionAdapterWarningsAllows you to enable or disable the BIOS warning messages when you use certain power adapters. The BIOS displays these messages ifyou attempt to use a power adapter that has too little capacity for your configuration.The factory default setting is Enabled.Keypad(Embedded)Allows you to select one of two methods to enable the keypad that is embedded in the internal keyboard.l Fn Key Only — The keypad is only enabled when you hold down the key.l By Num Lk — The keypad is enabled when (1) the Num Lock LED is on and (2) no external keyboard is attached. Note that thesystem might not notice immediately when an external keyboard is detached.NOTE: When Setup is running, this field has no effect—Setup works in the Fn Key Only mode.Default setting: Fn Key Only.Numlock LEDAllows you to enable or disable the Num Lock LED when the computer boots.Default setting: Enabled.USB EmulationDefines how the BIOS handles the USB devices. USB emulation is always enabled during POST.The factory default setting is Enabled.Fn Key EmulationAllows you to use the key on an external PS/2 keyboard the same way you use the key on the computer's internalkeyboard.NOTE: USB keyboards cannot emulate the key if you are running an ACPI operating system such as Microsoft® Windows® XP. USBkeyboards will only emulate the key in non-ACPI mode (e.g., when you are running a DOS).Default setting: Enabled.Fast BootAllows you to enable or disable the Fast Boot feature. The following options are available:l Minimal — Boot quickly unless the BIOS has been updated, memory changed, or the previous POST did not complete.l Thorough — Do not skip any steps in the boot process.l Auto — Allow the operating system to control this setting (this works only when the operating system supports Simple Boot Flag).Default setting: MinimalIntel Fast Call forHelpUsed in conjunction with iAMT 4.0. Allows users to initiate contact with a management console while residing outside of the corporateinfrastructure (i.e. remote location, behind a firewall or NAT, etc.) Use the check box to enable / disable this feature.