Delta DOP-108IG Series Instruction Sheet

DOP-108IG High color．Wide screen．User-friendlyDelta Electronics, Inc.No.18, Xinglong Rd., Taoyuan City33068, TaiwanInstruction Sheet(1) General precautionsThank you for purchasing this product. This DOP-108IG instruction sheet provides information for theDOP-108IG series HMI. Before using this product, please read through this instruction sheet carefully toensure the correct use of the product. Please keep this sheet handy for quick reference whenever needed.Before finishing reading this sheet, please follow the instructions below: Install the product in an indoor location, which is free of vapor and corrosive and inflammable gas. Please refer to the wiring diagram when connecting the wires. Ensure this product is correctly grounded. The grounding method must comply with the nationalelectrical standard guidelines (refer to NFPA 70: National Electrical Code, 2005 Ed.). Do not disassemble the HMI or change the wiring when power is on. Do not touch the power supply when power is on, or it may cause electric shock. When the HMI displays a low power notification and requires a battery change, please contactyour local distributor or Delta Customer Service Center for the replacement. Do not change thebatteries by yourself. This product can be used with other industrial automation equipment. Please read through thissheet carefully and install the product according to the instructions to avoid danger. Cleaning method: please use a dry cloth to clean the product. This product must be used at an altitude below 2,000 m (6561.68 ft). If the equipment is used in a manner not specified by the manufacturer, the protection provided bythe equipment may be impaired. For repair and maintenance, please contact Delta Electronics, Inc. Address: No.18, Xinglong Rd.,Taoyuan City, Taiwan. TEL: +886-3-3626301.If you have any inquiry during operation, please contact our local distributors or Delta Customer ServiceCenter. The instruction sheet may be revised without prior notice. Contact our distributors or download thelatest version from the Delta website (http://www.deltaww.com.tw/ia).(2) Communication port pin assignmentDOP-108IG COM1COM Port Pin MODE1RS-2321 -2 RXD3 TXD4 -5 GND6 -7 RTS8 CTS9 -Note: the mark “-” means connection is not required.DOP-108IG COM2COM Port Pin MODE1 MODE2 MODE3RS-232 RS-422 RS-4851 - TXD+ D+2 RXD - -3 TXD - -4 - RXD+ -5 GND GND GND6 - TXD- D-7 RTS - -8 CTS - -9 - RXD- -Note:1. The mark “-” means connection is not required.2. To use COM2 for flow control through RS-232 (RTS and CTS signals), COM3 port is not operable.DOP-108IG COM3COM Port Pin MODE1 MODE2 MODE3RS-232 RS-422 RS-4851 - TXD+ D+2 RXD - -3 TXD - -4 - RXD+ -5 GND GND GND6 - TXD- D-7 - - -8 - - -9 - RXD- -Note:1. The mark “-” means connection is not required.DOP-108IG Ethernet interface (LAN)Ethernet interface Pin ContactEthernet1 TX+2 TX-3 RX+4 -5 -6 RX-7 -8 -Note: the mark “-” means connection is not required.(3) Description of each partDOP-108IG (front view)A Operation / display areaDOP-108IG (rear view)A Power input connector F Audio output interfaceB COM3 (supports communication indicator) G USB HostC COM2 (supports communication indicator) H Ethernet interface (LAN)D COM1 I USB SlaveE Memory card slot / battery cover - -(4) Mounting dimensionsDOP-108IG(5) Installation and wiringPrecautions: Mount the HMI according to the illustration below. Incorrect installation direction may result inmalfunction. To ensure the HMI is well ventilated, make sure there is sufficient space between the HMI and theadjacent objects or walls. This product should be installed in a case or on a platform which conforms to enclosure Type 4Xstandard (for indoor use only). The maximum panel thickness for mounting must be no greater than 5 mm (0.2 inches). Please use copper wires.Installation diagram:Step 1:Put the waterproof gasket onto the HMI and theninsert the HMI into the panel cutout.Step 2:Place the fasteners into the slots and tightenthe screws until reaching the panel cutouts.Step 3:Tighten the screws with the torque between0.5 N-M and 0.7 N-M to avoid damage to theplastic case.DOP-108IG torque: 6.17 lb-inch (0.7 N-M)Step 4:For heat dissipation, please keep aminimum clearance of 60 mm (2.36 inches)and 45 mm (1.77 inches) respectively on therear and bottom of the HMI.Unit: mm (inches)