Delta DTD Series Instruction Sheet

Contents

ordering information

Delta DTD Series Instruction Sheet Manual pdf 1 page image

Http://www.delta.com.tw/industrialautomationSeries Temperature Controller Instruction SheetThank you very much for choosing Delta DTD series temperature controller. Please read this instruction sheet before using your DTD to ensure properoperation. Keep this instruction sheet handy for quick reference. WarningDANGER! CAUTION! ELECTRIC SHOCK! When the power is on, DO NOT touch the AC terminals in case an electric shock may occur. Make surethe power is disconnected when you check the input power.DTD is an OPEN-TYPE device. If it will cause serious injury to workers or damage on other equipments when used in a dangerous environment,please make sure it is installed in an automatic safety protection device.1. Always use recommended solder-less terminals: Fork terminal with isolation (M3 screw, Max. width 7.2mm). Please be sure to tightenthem properly and make sure the wire is connected to the correct terminal.2. Prevent dust or metallic debris from falling into the device and cause malfunctions. DO NOT modify or uninstall DTD series withoutbeing permitted. DO NOT use empty terminals.3. Keep away from high-voltage and high-frequency environment during installation in case of interference. Prevent using the device inpremises which contain:(a) dust or corrosive gas; (b) high humidity and high radiation; (c) shock and vibration4. The power has to be switched off when wiring or changing temperature sensor.5. Make sure to use compensation wire which matches the thermocouple when extending or connecting the thermocouple wire.6. Use wires with resistance when extending or connecting the platinum resistance sensor.7. Keep the wire as short as possible when wiring a sensor to the temperature controller. Separate the power cable and load wire inorder to prevent interference and induced noise.8. DTD is an open-type device. Make sure to install it in an enclosure which prevents dust and humidity in case of an electric shock.9. Make sure the power cables and signal device are installed correctly before switching on the power; otherwise serious damage mayoccur.10. DO NOT touch the terminals or repair the device when the power is on; otherwise an electric shock may occur11. Please wait for one minute after the power is switched off to allow the capacitor to discharge and DO NOT touch the internal wiringwithin this period. Use dry cloth to clean the device. DO NOT use acid or alkaline liquid to clean the device. Display, LED & PushbuttonsPV Present value/function display(red 7-segment LED)SV Set value(green 7-segment LED)AT Flashes when PID auto-tuning(green LED)OUT On when output (green LED)ALM On when alarm (red LED)Selecting modescompleting setupDisplaying functionsLeft-shifting the digit Ordering InformationDTD 01 2 3 4 5Series name DTD: Delta D series temperature controller1!Up key2 3 4Panel size(W × H)4848: 1/16 DIN W48 × H48 mm4896: 1/8 DIN W48 × H96 mm7272: W72 × H72 mm5R: Relay output SPST (250VAC, 5A)V: Voltage pulse output 14V +10% ~ -20%(Max. 40mA)Optional 0: None SpecificationsPower input AC100 ~ 240V 50/60HzInput power range 85% ~ 110%, rated voltagePower consumption 6VA Max.Display 7-segment LED; PV in red, SV in greenInput temperaturesensorThermocouple: K, J, T, E, N, R, S, B, U, L, Txk Platinum resistance: Pt100, JPt100Copper resistance: Cu50Analog input Current: 0 ~ 20mA, 4 ~ 20mA Voltage: 0 ~ 5V, 0 ~ 10V, 0 ~ 70mVDisplay scale For temperature input: K2, J2, T2, Pt100-2, JPt100 and Cu50 can display to 0.1 degree; others display in1degree as a unit.Control method PID, PID programmable control, On/Off, manual outputRelay output: AC 250V, 5A, SPSTControl output type Voltage pulse output: DC 14V, Max. output current 40mASampling cycle 0.4 second (including analog input signal and sensor input signal)Vibration resistance 10 ~ 55Hz 10m/s 2 3 axes 10minsShock resistance Max. 300m/ s 2 3 axes 6 directions, 3 times eachAmbient temperature 0°C ~ 50°C1