Denon AVC-A11XVA Service Manual

Also see for AVR-4806CI: User manual Capabilities and Compatibilities Guide Operating instructions Specifications

Contents

30AVR-4806CI / AVC-A11XVA103 P10 VSEL2/TDI O C - - Ed Z O/L O/L BUS SW(PLD) control pin104 P07/AN07 NC O C - - - Z O/L O/L Not used105 P06/AN06 NC O C - - - Z O/L O/L Not used106 P05/AN05 VD RST O - - - - Z O/L O/L VIDEO DECODER reset (ADV7403)107 P04/AN04 NC O C - - - Z O/L O/L Not used108 P03/AN03 NC O C - - - Z O/L O/L Not used109 P02/AN02 VE RST O - - - - Z O/L O/L VIDEO ENCODER reset (ADV7320)110 P01/AN01 NC O C - - - Z O/L O/L Not used111 P00/AN00 INT1 I - - - Eu Z I O/L HDMI RECEIVER(Si I9033)INT output (DVI IN1/HDMI IN1)112 P117 INT2 I - - - Eu Z I O/L HDMI RECEIVER(Si I9033)INT output (HDMI IN2/IN3)113 P116 HDMI R RST O C - - Ed Z O/L O/L HDMI RECEIVER reset (Si I9033) (HDMI IN2/IN3)114 P115 DVI R RST O C - - Ed Z O/L O/L HDMI RECEIVER reset (Si I9033) (DVI IN1/HDMI IN1)115 P114 SCDT1 I - - - Eu Z I O/L HDMI RECEIVER(Si I9033)SCDT output (DVI IN1/HDMI IN1)116 P113 SCDT2 I - - - Eu Z I O/L HDMI RECEIVER(Si I9033)SCDT output (HDMI IN2/IN3)117 P112 WP1 O C - - Ed Z O/L O/L HDMI IN1 EDIT(24LC02) WRITE PROTECT118 P111 WP2 O C - - Ed Z O/L O/L HDMI IN1 EDIT(24LC02) WRITE PROTECT119 P110 WP3 O C - - Ed Z O/L O/L HDMI IN1 EDIT(24LC02) WRITE PROTECT120 P107/AN7 WP4 O C - - Ed Z O/L O/L HDMI IN1 EDIT(24LC02) WRITE PROTECT121 P106/AN6 NC O C - - - Z O/L O/L Not used122 P105/AN5 Z1 S SIG DET I - - - Eu Z I O/L MAIN ZONE's S-signal detect input (H: S-signal inputted)123 P104/AN4 NC O C - - - Z O/L O/L Not used124 P103/AN3 NC O C - - - Z O/L O/L Not used125 P102/AN2 NC O C - - - Z O/L O/L Not used126 P101/AN1 NC O C - - - Z O/L O/L Not used127 AVSS AVSS - - - - - - - - AD GND128 P100/AN0 NC O C - - - Z O/L O/L Not usedPin Pin Name Symbol I/O Type Det Op(Int.)Op(Ext.) Res STBY stop FUNCTIONNote: Pin No. : Terminal number of microcomputer.Port Name : The name entered in the data sheet of microcomputer.Symbol : Symbolized interface function.I/O : Input or out of part.“I” = Input port“O” = Output portType : Composition of port in case of output port.“C” = CMOS output“N” = NMOS open drain output“P” = PMOS open drain outputOp : Pull up/Pull down selection information.“Iu” = Inner microcomputer pull up“Id” = Inner microcomputer pull down“Eu” = External microcomputer pull up“Ed” = External microcomputer pull downDet : Indicates judging state of input port. Level detection is “LV”; Edge detection is “Ed”; Detection by both shifting is “E&L”;Serial data detection is “S” (Serial data output is also “S”).Res : State at reset.“H” = Outputs High Level at reset“L” = Outputs Low Level at reset“Z” = Becomes High impedance mode at resetSTBY : State of port when STANDBY mode.“O/L” = Output port and “L”“I” = Input portStop : State of port when Stop mode.“O/L” = Output port and “L”“I” = Input port