Denon AVC-A1XV Operating Instructions Manual

Also see for AVC-A1XV: Operating instructions Supplementary guide Manual Operating instructions Service manual

Denon AVC-A1XV Operating Instructions Manual Manual pdf 7 page image

System Setup System Setup6ENGLISHENGLISHSet the format of the signal up-converted to the HDMI monitor outputor component output terminal.Press DD HH to select “HDMI/Component Out”, thenpress ENTER.Press DD HH to select the item, then press FF GG to set.23Analog to HDMI Convert:• ON:Setting for converting analog video signals into HDMI signals.• OFF:Setting for not converting analog video signals into HDMI signals.Scaler:• HDMI:The i/p scaler can be used when outputting the input analog videosignal to the HDMI monitor output terminal.• Component:The i/p scaler can be used when outputting the input analog videosignal to the component output terminal.When “Analog to HDMI Convert” is set to “OFF”, the “Scaler”setting is automatically set to “Component” and fixed there.Aspect:• FULL:The video is output while maintaining the aspect ratio of the inputvideo.This mode is suited for playing back 16:9 video.• NORMAL:A black band is added to the left and right of the input video andthe video is output.This mode is suited for playing back 4:3 video.Setting the HDMI/Component Out Resolution:• 480p/576p:When the video signal input is a video, S-Video or 480i/576icomponent video signal, the resolution is converted to 480p/576pand the signal is output from the monitor output terminal.• 1080i:When the video signal input is a video, S-Video or480i/576i/480p/576p component video signal, the resolution isconverted to 1080i and the signal is output from the monitoroutput terminal.• 720p:When the video signal input is a video, S-Video or480i/576i/480p/576p component video signal, the resolution isconverted to 720p and the signal is output from the monitor outputterminal.• 1080p:The input video signal is converted to a resolution of 1080p foroutput.This cannot be selected when “Scaler” is set to “Component”.• Through:The video signal input is output as such from the monitor outputterminal without being converted.Color Space:• Y Cb Cr:The Y Cb Cr format video signals is output via the HDMI outputconnector.• RGB:The RGB format video signals is output via the HDMI outputconnector.RGB Mode Setup:• Normal:Signals are output via the HDMI output connector with a digitalRGB video range (data range) of 16 (black) to 235 (white).• Enhanced:Signals are output via the HDMI output connector with a digitalRGB video range (data range) of 0 (black) to 255 (white).Press DD HH to select “Video Setup” at the “SystemSetup Menu”, then press ENTER.1Press ENTER.4When the HDMI connectors are connected, the black may seemto stand out, depending on the TV or the monitor. In this case, setthis to “Enhanced”.When “Y Cb Cr” is selected under “Color Space”, “RGB ModeSetup” will have no effect.The aspect ratio setting is valid when the resolution is set to1080i, 720p or 1080p. To output with other resolutions, set theaspect ratio on the TV.When “Through” is set, the signal is output with the sameresolution as input from the video, S-Video and component videoterminals.The on screen display, however, is output with a resolution of480i, so use a monitor compatible with this resolution.• “Scaler”, “Color Space” and “RGB Mode Setup” are only displayedwhen “Analog to HDMI Convert” is set to “ON”.• When connecting to an HDCP compatible monitor equipped withDVI-D terminal, the signals are output in RGB format, regardless ofthe “Color Space” setting.• To view the on screen display using an HDMI monitor, set “Analogto HDMI Convert” at “HDMI/Component Out” to “ON” (default).• Set the resolution of the video output to one that is compatible withthe resolution of your monitor.• When “Scaler” is set to “Component” and the video input signalincludes copyright protection data, the signal is output from thecomponent video output terminal with a resolution of 480p/576peven if “Resolution” is set to “1080i” or “720p”.2 3