Denon AVR-2801 Operating Instructions Manual

Also see for AVR-2802: Operating instructions Brochure & specs Operating instructions Operating instructions Service manual

Denon AVR-2801 Operating Instructions Manual Manual pdf 14 page image

ENGLISH14TUNINGBANDTITLE MENU/GUIDEMODEMEMORYUSE/LEARN T.TONERETURNDVDSET UPSTATUSDISPLAYON SCREENMUTINGAVR/AVC VIDEO DVD TVAUDIOVDP VCRCD CDR/MDDECKSYSTEMSETUPSURROUNDPARAMETERCH SELECTSELECTENTER7 SETTING UP THE SYSTEM• Once all connections with other AV components have been completed as described in “CONNECTIONS” (see pages 6 to 11), make the varioussettings described below on the monitor screen using the AVR-2801/981’s on-screen display function.These settings are required to set up the listening room’s AV system centered around the AVR-2801/981.• Use the following buttons to set up the system:SYSTEM SETUP buttonPress this to display the system setup menu.SURROUND PARAMETER buttonPress this to display the surround parameter menu.ENTER buttonPress this to switch the display on the screen.Also use this button to complete the setting on the screen.CURSOR buttonsand : Use these to move the cursors (0 and 1) to the left and righton the screen.and : Use these to move the cursors (• and ª) up and down on thescreen.• System setup items and default values (set upon shipment from the factory)System setup Default settingsqwertySpeakerConfigurationSubwoofer modeDelay TimeChannelLevelDigital InAdjutmentOn ScreenDisplayAuto TunerPresetsInput the combination of speakers in your system and theircorresponding sizes (SMALL for regular speakers, LARGE for full-size,full-range) to automatically set the composition of the signals outputfrom the speakers and the frequency response.This selects the subwoofer speaker for playing deep bass signals.This parameter is for optimizing the timing with which the audiosignals are produced from the speakers and subwoofer according tothe listening position.This adjusts the volume of the signals output from the speakers andsubwoofer for the different channels in order to obtain optimumeffects.This assigns the digital input jacks for the different inputsources.This sets whether or not to display the on-screen display that appearson the monitor screen when the controls on the remote control unit ormain unit are operated (from MONITOR outputs only).FM stations are received automatically and stored in the memory.InputsourceDigitalInputsFront Sp. Center Sp. Surround Sp. SubwooferSmallCenter3.6 m (12 ft)Surround L & R —3.0 m (10 ft) —Small YesLargeLFEFront & Subwoofer3.6 m (12 ft)Front L0 dBCDCOAXIALOn Screen Display = ONA1 ~ A8B1 ~ B8C1 ~ C8D1 ~ D8E1 ~ E887.5/89.1/98.1/107.9/90.1/90.1/90.1/90.1 MHz520/600/1000/1400/1500/1710 kHz/90.1/90.1 MHz90.1 MHz90.1 MHz90.1 MHzFront R0 dBDVDOPTICAL 1Subwoofer0 dBVDPOPTICAL 2TV/DBSOPTICAL 3VCR-1OFFVCR-2/V. AUX — —OFF — —Center0 dBSurround L0 dBSurround R — —0 dB — —NOTES:• The on-screen display signals are output with priority to the S-VIDEO MONITOR OUT jack during playback of a video component. For example,if the TV monitor is connected to both the AVR-2801/981’s S-Video and video monitor output jacks and signals are input to the AVR-2801/981from a video source (VDP, etc.) connected to both the S-Video and video input jacks, the on-screen display signals are output with priority tothe S-Video monitor output. If you wish to output the signals to the video monitor output jack, do not connect a cord to the S-VIDEOMONITOR OUT jack. (For details, see page 22.)• The AVR-2801/981’s on-screen display function is designed for use with high resolution monitor TVs, so it may be difficult to read smallcharacters on TVs with small screens or low resolutions.• The setup menu is not displayed when “HEADPHONE ONLY” is selected.