Denon DN-C635 Operating Instructions Manual

Also see for DN-C635: Operating instructions Service manual Service manual

Contents

Denon DN-C635 Operating Instructions Manual Manual pdf 14 page image

14ENGLISHExternal synchronized recordingThe synchronized recording can be use when the DN-C635 is used in combination with DENON other product(DN-780R etc.).When the CD player’s play button is pressed, a synchronized signal for starting is output from the EXT. SYNC.jack. When the STOP buttons on the CD player is pressed, a synchronized signal for stopping is output from theEXT. SYNC. jack.• Refer to figure 2 to connect the equipment.• Use a single RCA cable to connect the units’ EXT. SYNC. OUT jacks with the units’ EXT. SYNC. IN jacks.✽ Set the infrared remote sensors of all the units to “OFF” when using this function. Also set the same infraredremote control codes for all the units. (Refer to “PRESET FUNCTIONS AND OPERATIONS” (See page 14).)Failure to make these settings could result in malfunction.1. Load the CD into DN-C635. Load unrecorded cassette tapes into all decks.2. Set the reverse mode and Dolby NR of all decks.3. Adjust the twin recording level of DN-780Rs. (Master/Slave switch set to OFF.)4. Press the Twin recording button of DN-780R.5. Press the PLAY (1) button y of DN-C635. Recording starts all decks.6. Press the STOP (2) button u of the DN-C635 to stop recording on all the connected units.NOTE:• Use tapes of the same times (lengths) as far as possible.L RLRFigure 2DN-780RDN-C635Preset typeFinish modePower on modeAuto cueAuto stopProgram 1Program 2Program 3End monitorE.O.M.Next track standbyNext Track ReservePlay speedDelay startPanel lockPlay lockEject lockTime modeFrame displayText display11 BEFORE SWITCHING OFF THE POWERWhen you have finished using the CD player, before switching off the power be sure that the disc holder has beenclosed with the OPEN/CLOSE (5) button.CAUTION:• Do not forcibly close the disc holder when the power is off. It may damage the unit when it is transported.12 PRESET FUNCTIONS AND OPERATIONS(1) List of Preset Functions• Functions can be preset using the buttons on the front panel. These presettings are stored in a permanentmemory, so they are not cleared even when the power is turned off.• The functions shown on the table below can be preset. Set the functions according to the usage purpose toefficiently achieve even higher quality playback.• One of the preset functions can be used to display information on this set (microprocessor version).Selection of preset type.Setting of operation when playback ends.Setting of operation when power is turned on.Setting of whether or not to perform the auto cueoperation and the audio startup level.Setting of whether or not to automatically stop the servofunctions.Setting of whether or not to play program 1.Setting of whether or not to play program 2.Setting of whether or not to play program 3.Setting of whether or not to use the end monitor functionand monitor time setting.Setting of whether or not to display the EOM and displaytime setting.Setting of whether or not to standby at the next trackwhen the CUE button is pressed during playback.Setting of operation when select knob is turned duringplayback.Standard playing speed setting.Delay start time setting.Selection of whether or not to enable the panel buttons.Selection of whether or not to inhibit the panel switchesduring playback.Selection of whether or not to lock ejecting duringplayback.Setting of play mode when power is turned on.Selection of whether or not to display frames.Selection of time or text display.Preset Type 1Finish NextPower On StandbyCueDet. -48dBSleep 30minProgram 1 OFFProgram 2 OFFProgram 3 OFFEnd Mon. 10 sE.O.M. 10 sNext Stb. OFFReserve. OFFNormal SpeedDelay OFFPanel OFFPlay Lock OFFEject OFFTime REMAINFR Disp ONText OFF1234567891011121314151617181920Preset function type Description Set upon shipmentfrom factory No.