14ENGLISH2. Disc tray auto close1Disc tray will automatically close after 30seconds have elapsed for the disc tray autoclose mode. (Preset item 3)3. End of message1During playback, the Play Position indicatorsstart flashing when the remaining playingtime to the end of the track (set in the presetmode)is reached, indicating that the end ofthe track is near. (Preset item 6)4. Power on play1 When “Power On Play”is set to “ON” mode at“⁄1 PRESET (8)”, playback starts from the firsttrack on the disc when the power is turned on.1. Relay play• The unit can play CD1 and CD2 alternately.• The relay mode is set when the CONT./SINGLEbutton u is pressed for over 1 second.(1) Single relay mode1Press the CONT./SINGLE buttonu several times until “SINGLE”indicator flashes on the display.• When playback is finish of thedesired track, the oppositedrive will start to play.• When both CD1 and CD2 set to the SINGLERELAY mode, endless play is available forthe each track of CD1 and CD2 alternately.(2) Continuous relay mode1Press the CONT./SINGLE button useveral times until “CONTINUOUS”indicator flashes on the display.• When playback is finish for thefinal track on the target disc,the opposite drive will start toplay.• When both CD1 and CD2 set to theCONTINUOUS RELAY mode, endless play isavailable for each disc of CD1 and CD2alternately.10 MEMO (Custom Setting Memory)CD setting information can be stored in the non-volatile memory. The stored information can be called out of thememory later, making it easy to prepare for your mixing.NOTE: The MEMO function cannot be used for MP3.1. About TRACK MEMO• Up to 1000 memo points can be stored to internal memory for later recall.The number of tracks on a particular CD only limits the amount of memo points available per that disc.Example: If your CD has 22 tracks, you can only save up to 22 memos. (1 memo group per track.)CAUTION:1000 is the maximum possible number of tracks that can be stored to memory.However, to simplify the MEMO operations, the memory system manages each 200 MEMO data groupsas a minimum unit (the total 1000 memory capacity divided into 5 memory data groups). When you wantto clear just one MEMO data in the 1 MEMO CLEAR mode (see page 15), the unit will erase the memoinformation but not the internal memo allocation number. Accordingly, depending on conditions, thenumber of tracks that can be stored in the memory may be fewer than 1000.Once you reached 1000 stored points, you will see a message that says “MEMO FULL!”. At this time youwill need to “delete” old data to make room for new memo points. Therefore the oldest 200 memo pointsin that group will be deleted and become available.• The MEMO indicator on the display lights up when a track for which data is stored in the memory isselected.2. MEMO ITEMSThe following items are max to be stored under 1 memory bank:q CUE point.w A1 and B1 points, A2 and B2 points.e Playing pitch, pitch range pitch on/off, Key Adjust on/off, Hot Start/Stutter setting.3. MEMO MODE SELECTq Push the MEMO button @4 in CUE mode to enter MEMO mode.w Turn the TRACK SELECT knob o to select the various MEMO modes from as follows.Memo Set, MemoCall, Memo ClrDepending on conditions, some modes cannot be selected.e Push the MEMO button @4 again to exit MEMO mode.(1) Storing data in the memory [Memo Set]• After making your desired settings to be stored in memory, then push CUE button !0.• In CUE mode, push MEMO button @4 once to enable Memo set function.• If the MEMO indicator is already lit up, it is necessary to clear existing Memo before storing a newMemo.• At last push TRACK SELECT knob o down to save. You can see “Complete!” message and MEMOindicator lights up.MEMO FULL• If the memory is full and no more data can be stored, “Memo Full!” and “Del. 200?” message appears.• In this case, you need to clear memory of First 200s Memo (number 1 to 200) at a time to make spacefor new memos.• To make space, push TRACK SELECT knob o down while “Del. 200?” message is displayed.• “Delete OK?” message appears then push TRACK SELECT knob o down again to execute clearing.• After the first 200s Memo (number 0 to 199) are cleared, number after 200 Memo are renumbered asnew 1, 2, 3…(now you have a new set of 200 empty spaces.).9 OTHER FUNCTIONSManual searchFor only C.B.R files, manual searching can be performed.NOTE:•With manual searching, it is only possible tosearch within the selected file.•Manual searching in the reverse direction ispossible up to the point 5 seconds before the pointat which searching starts.•The searching speed may vary according to thefile’s compression rate, etc.•V.B.R. is not supported with this function.Seamless Loop/Hot start/Stutter/BTrimFor only C.B.R. files, Hot starting, seamless loopplayback, stuttering and B trim can be performed inthe same way as with normal CDs.NOTE:•The A and B points for the seamless loop mustboth be set within the same file.•V.B.R. is not supported with these functions.BRAKEBRAKE is supported in the same way as with normalCDs.