Denon DN-X800 Operating Instructions Manual

Contents

Denon DN-X800 Operating Instructions Manual Manual pdf 9 page image

9ENGLISH7 REPLACING THE CROSSFADERThe Crossfader may be removed without any disassembly of the DN-X800 itself, and may be performed while the unit is operatingwith no interruption of the audio signal.1. Remove the two (2) outer screws attaching the crossfader assembly to the front panel.2. Pull the Crossfader Assembly forward and unplug the ribbon from the connector on the panel board.3. Install the replacement assembly by reversing the above instructions.8 SPECIFICATIONS GENERALDimensions: 482 (W) x 105 (H) x 177 (D) mm (without feet)Installation: 19-inch rack mountable 4UMass: 5.5 kgPower supply: 230 V AC ±10%, 50 Hz (Europe model)220 V AC ±10%, 50 Hz (China model)Power consumption: 26 WEnvironmental conditions: Operational temperature: 5 to 35°C (41 to 95°F)Operational humidity: 25 to 85% (no condensation)Storage temperature: -20 to 60°C (4 to 140°F) AUDIO SECTIONInput Sensitivity & Impedance:Main Mic -54 dBV (2.0 mV) 10 kΩ/kohmsAux Mic -60 dBV (1.0 mV) 10 kΩ/kohmsEffect (Return) -14 dBV (200 mV) 50 kΩ/kohms3-Phono -50 dBV (3.0 mV) 50 kΩ/kohms8-Line -14 dBV (200 mV) 50 kΩ/kohmsOutput level & Impedance:Main (Balanced) 4 dBm (1.23 V) 600 Ω/ohms loadMain (Unbalanced) 0 dBV (1.0V) 1 kΩ/kohmsZone (Balanced) 4 dBm (1.23 V) 600 Ω/ohms loadBooth (RCA) 6 dBV (2.0 V) 1 kΩ/kohmsTape (RCA) -10 dBV (316 mV) 1 kΩ/kohmsEffect (Send) -14 dBV (200 mV) 1 kΩ/kohmsSubwoofer -2 dBV (800 mV) 1 kΩ/kohmsHeadphone -4 dBV (630 mV) 150 Ω/ohmsFrequency Response:Line 20 to 20 kHz ±2 dBPhono 20 to 20 kHz RIAA ±2 dBMic 20 to 20 kHz ±2 dBSignal to Noise ratio:Line 80 dB 0 dBm, 1 kHz, EQ flatPhono 75 dB 0 dBm, 1 kHz, EQ flatMain Mic 65 dB 0 dBm, 1 kHz, EQ flatTotal harmonic distortion rate:Line Below 0.05%Phono Below 0.05%Cross talk: Over 70 dBChannel equalizer:Hi +10 dB, -26 dB (13 kHz)Mid +10 dB, -26 dB (1 kHz)Low +10 dB, -26 dB (100 Hz)Microphone equalizer:Hi +12 dB, -12 dB (10 kHz)Mid +12 dB, -12 dB (1 kHz)Low +12 dB, -12 dB (100 Hz)Digital input:Input sensitivity -20 dBV (100 mV)Signal format SPDIFOutput level 0.5 Vp-p 75 Ω/ohmsDigital output:Signal format IEC958 Type IIOutput level 0.5 Vp-p 75 Ω/ohmsOutput signal level -6 dB✽ Specifications and design are subject to change without notice for purpose of improvement.