Denon DRA-F101 Operating Instructions Manual

Also see for DRA-F101: Operating instructions Specifications Operating instructions Operation instruction Service manual

Contents

Denon DRA-F101 Operating Instructions Manual Manual pdf 8 page image

TIME: Use this to set the time.EVERYDAY: Use this to set the everyday timer.ONCE: Use this to set the once timer.• Press this button during in STANDBY mode toswitch ON/OFF (“Saving Energy Mode”) the clockdisplay.!3 Tone button (TONE)• Use this to set the bass, treble and balance level.(Refer to pages 12, 13.)• Use this to set the loudness function to on or off.(Refer to page 13.)8ENGLISH5 PART NAMES AND FUNCTIONS(1) Front Panelq Power operation switch (ON/STANDBY)• This turns the power for the entire system on andoff.• Press this once to turn the power on, then pressagain to set the power to STANDBY mode.• The LED color changes as follows, according tothe condition:During power ON : greenDuring STANDBY : redDuring TIMER STANDBY: orange✻ The muting mode is set when the main unit’spower button is pressed and when the standbymode is canceled from the remote control unit.The power indicator flashes green when in themuting mode, then stops flashing and turns greenonce the set is in the operational mode.✻ If the indicator is flashing orange (quickly):The protective circuit is activated.If this happens, unplug the power cord to turn theindicator off, then check the input and outputterminals on the rear panel. Check in particular forshort-circuiting of the speaker cords. Once allconnections have been corrected, plug the powercord. (Wait for at least 10 seconds after turningthe power off before turning it back on.)• When the DRA-F101 is connected in a systemwith the DCD-F101, its power button works as thepower button for the entire system. When theDRA-F101’s power turns on, the power of theDCD-F101 also turns on.✻ Power is supplied to the DRA-F101 even whenthe power is in the standby mode (low powerconsumption).w REMOTE SENSOR (Remote Control Sensor)• Point the included remote control unit (RC-927) atthis sensor when operating it.e Headphones jack (PHONES)• Use this jack to listen to the sound overcommercially available headphones.• When the headphones’ plug is inserted into thejack, the speaker output is automatically cut off,so no sound is produced from the speakers.r Function dial (FUNCTION)• Switches the input function. Also used to set themodes selected with the mode button.(See pages 12, 13.)t DisplayRefer to page 9.y Volume control dial (VOLUME)• Use this to adjust the overall volume. (RotaryEncoder System).• The volume increases when the control is turnedclockwise (, ), decreases when it is turnedcounterclockwise (.).• The volume increases and decreases in 63 stepsfrom the minimum (VOLUME 0) to the maximum(VOLUME MAX).u Source direct button (SOURCE DIRECT)• When pressed and set to the “ON” position, thetone control (bass, treble, balance and loudness)circuits are set into default condition.• When pressed again and set to the “OFF”position, the signals pass through the tone controlcircuits, so the tone (bass, treble, balance andloudness) can be adjusted as desired.i Band button (BAND)• Each time this button is pressed, the band and FMreception mode change as follows.CLOCK: Indicates the current time.TIMER STANDBY: Indicates the timer standbymode. Use the TUNING buttons to set the timerstandby mode on or off (refer to page 16).• Press this buttons for at least 3 seconds to set thetimer (refer to page 15) or to confirm the timercontents (refer to page 16).Each time the TUNING button is pressed, thedisplay changes as follows:TIME EVERYDAY ONCEFUNCTIONTIMER STANDBYCLOCKTIME FUNCTIONFM AUTO FM MONO AM!2 Timer button (TIMER)• Press this button during power ON mode toconfirm or change the display. Each time thisbutton is pressed, the display changes as follows:o Tuning buttons(TUNING UP AND DOWN)• Use these buttons to tune in AM and FM stations.(TUNING UP/DOWN) (See page 13.)!0 Memory/set button (MEMORY/SET)• Use this as the memory button when presettingAM and FM stations.• Use this as the set button when setting the timeand timer and when inputting data.• When the PTY search mode, press this button toselect the type of program.!1 Display button (DISPLAY)Each time this button is pressed, the displaychanges as follows:!4 SIGNAL GND (ground) terminal• Connect the turntable’s ground wire here.!5 INPUT terminals (INPUTS)These are input terminals for CD player, turntable,DVD or other playback components.!6 TAPE and MD PLAY terminals (PB)• Playback terminals (PB)!7 TAPE and MD REC terminals (REC)• Recording terminals (REC)• These are output jacks for recording.• TAPE:Use these to connect a cassette deck.• MD:Use these to connect an MD recorder!8 PRE OUT terminal (SUB WOOFER)• Connector jack for subwoofer with built-inamplifier (super woofer), etc.!9 AC OUTLET• When using in combination with the DCD-F101,connect DCD-F101 to the AC outlet on thereceiver (DRA-F101).@0 Power cord• Plug this cord into a wall power outlet.@1 Speaker terminals(SPEAKER SYSTEM)• Use these to connect the speakers.@2 System connectors(SYSTEM CONNECTOR 1 and 2)• When connecting the DCD-F101 in a system,connect these connectors to system connectorson DCD-F101.(Use the system cord included with the DCD-F101.)@3 AM antenna terminal(ANTENNA TERMINAL AM)• Connect the AM antenna here.@4 FM antenna terminal(ANTENNA TERMINAL FM)• Connect the FM antenna here.(2) Rear PanelNOTE:• This terminal is designed to reduce noisewhen a turntable is connected.This is not a safety ground.