Denon DVD-910 Service Manual

Also see for DVD-910: Operating instructions Specifications Operating instructions Service manual Operating insructions

Contents

1010DVD-910CABINET DISASSEMBLY INSTRUCTIONS1. Disassembly FlowchartThis flowchart indicates the disassembly steps to gainaccess to item(s) to be serviced. When reassembling,follow the steps in reverse order. Bend, route, anddress the cables as they were originally.2. Disassembly Method(1): Identification (location) No. of parts in the figures(2): Name of the part(3): Figure Number for reference(4): Identification of parts to be removed, unhooked,unlocked, released, unplugged, unclamped, or des-oldered.P=Spring, L=Locking Tab, S=Screw,CN=Connector*=Unhook, Unlock, Release, Unplug, or Desoldere.g. 2(S-2) = two Screws (S-2),2(L-2) = two Locking Tabs (L-2)(5): Refer to “Reference Notes.”Reference NotesCAUTION 1: Locking Tabs (L-1), (L-2) and (L-3) arefragile. Be careful not to break them.1-1. Connect the wall plug to an AC outlet and pressthe OPEN/CLOSE button to open the Tray.1-2. Remove the Tray Panel by releasing two LockingTabs (L-1).1-3. Press the OPEN/CLOSE button again to close theTray.1-4. Press the POWER button to turn the power off.1-5. Unplug an AC cord.1-6. Disconnect connector CN6401.1-7. Release two Locking Tabs (L-2). Then, releasefive Locking Tabs (L-3) (to do this, first release twoLocking Tabs (A) at the side, and then three Lock-ing Tabs (B) at the bottom.)CAUTION 2: Electrostatic breakdown of the laser diodein the optical system block may occur as a potential dif-ference caused by electrostatic charge accumulated oncloth, human body etc, during unpacking or repairwork.To avoid damage of pickup follow these procedures.2-1. Slide out the pickup unit as shown in Fig. D5.2-2. Short the three short lands of FPC cable with sol-der before removing the FFC cable (CN201) fromit. If you disconnect the FFC cable (CN201), thelaser diode of pickup will be destroyed. (Fig. D5)2-3. Disconnect connector (CN301). Remove threescrews (S-2) and lift the DVD Mecha. (Fig. D4)CAUTION 3: When reassembling, confirm the FFCcable (CN201) is connected completely. Then removethe solder from the three short lands of FPC cable.(Fig. D5)ID/LOC.No.PARTREMOVALFig.No.REMOVE/*UNHOOK/UNLOCK/RELEASE/UNPLUG/DESOLDERNote[1] Top Cover D1 5(S-1) -[2] Front Unit D2*2(L-1), Tray Panel,*2(L-2), *5(L-3),CN64011-11-21-31-41-51-61-7[3] FrontAssembly D3 ---------- -[4] FunctionCBA D3 6(S-2),Insulation Sheet -[5] DVD Mecha D4,D53(S-3), *CN201,*CN30122-12-22-33[6] Shield Plate D4 (S-4) -[7] ProgressiveCBA Unit D4 2(S-5), CN6101,CN202 -[8] DVD MainCBA Unit D4 2(S-6), CN1001,CN1601 -[9] Holder D4 (S-7) -[10] AV CBA D6 5(S-8), 5(S-9), (L-4) -[11] Switch CBA D6 Desolder -[12] Rear Panel D7 3(S-10) -↓(1)↓(2)↓(3)↓(4)↓(5)[1] Top Cover[2] Front Unit[3] FrontAssembly[5] DVD Mecha[6] Shield Plate[4] FunctionCBA[7] Progressive CBA Unit [10] AV CBA[8] DVD Main CBA Unit[9] Holder[11] Switch CBA[12] Rear Panelwww. xiaoyu163. comQQ 376315150 992894298TEL 13942296513 992894298051513673QQTEL 13942296513 QQ 376315150 892498299TEL 13942296513 QQ 376315150 892498299http://www.xiaoyu163.comhttp://www.xiaoyu163.com