Denon dra-f101 Operation Instruction Manual

Also see for DRA-F101: Operating instructions Specifications Operating instructions Operating instructions Service manual

Contents

Denon dra-f101 Operation Instruction Manual Manual pdf 16 page image

16ENGLISH9 USING THE TIMER(1) Setting the Current Time (24-hour display)Example: Setting the current time to 19:301 Turn on the power.2Press the TIMER button for at least3 seconds.• “TIME” flashes on the display.✽ If the time is already set,“EVERYDAY” is displayed.Press one of the TUNING buttonsto display “TIME”, then performstep 3.7Press the MEMORY/SET buttonat the sound of the chime of atime service, etc.• “30” stops flashing, remaininglit, and the current time isdisplayed.✽ The number changes continuously when one of thetuning buttons (TUNING UP or DOWN) is pressed.✽ If the time is already set when step 2, 3 is performed,both the hours and minutes positions flash.MEMORY/ SETPHONESSYSTEMVOLUMEON / STANDBYAM-FM STEREO RECEIVER DRA-F101SOURCEDIRECTBANDUPDOWNTUNINGMEMORY/ SETFUNCTION TIMERTONE RDS2 3,5,7 4,61SYSTEMON / STANDBYTIMER5Press the MEMORY/SET button.• “19” stops flashing, remaininglit, and the minutes positionstarts flashing.MEMORY/ SETUse the TUNING buttons toinput the minutes (30).• “30” flashes in theminutes position.6UPDOWNTUNING3Press the MEMORY/SET button.• The hours position flashes.MEMORY/ SETUse the TUNING buttonsto input the hours (19).• “19” flashes in the hoursposition.4UPDOWNTUNING(2) Before Setting the Timer2 Be sure to set the current time. If the current time is not set, the timer standby indicator (“ ”) will not light and thetimer will not function.2 Be sure to preset the station before setting the timer. (Refer to “Presetting AM and FM stations” on page 14.)2 The DRA-F101 is equipped with two types of timers: the everyday time which turns the power on and off at thesame times every day, and the once timer that turns the power on and off only once.2 Do not change the timer standby mode after the timer is activated (after the timer on time is reached). The timer maynot operate properly.2 It is not possible to set the timer start and end times to the same time.2 If the display or operation is not normal, unplug the power cord, then plug it back in while pressing the memory/setbutton (MEMORY/SET). This restores the tuner to the initial default values. After doing this, reset the presettings,current time and timer settings.2 When setting the timer to operate the CD player, MD recorder or cassette deck, do so with a disc or cassette loadedand the disc holder or cassette holder closed. The timer will not operate properly if no disc or cassette is loaded or ifthe disc holder or cassette holder is open.(3) Setting the Timer2 The timer function lets you switch the power betweenthe on and standby modes automatically at the desiredtimes.2 When connected in a system with the D-F101 series,the timer can be used to play a CD, cassette or MD orto record from the tuner onto the MD recorder orcassette deck (“air check”).Example: Using the everyday timer to listen to thestation stored at preset number 3 (FM 98.00 MHz)from 12:35 to 12:561 Turn on the power.2Press the TIMER button for at least3 seconds.• “EVERYDAY” is displayed.TIMERSYSTEMON / STANDBYPHONESSYSTEMVOLUMEON / STANDBYAM-FM STEREO RECEIVER DRA-F101SOURCEDIRECTBANDUPDOWNTUNINGMEMORY/ SETFUNCTION TIMERTONE RDS2 3, 5, 7, 9,11,13,15,171,18 4, 6, 8,10,12,14,16✽ If the time is not set, “TIME” is displayed.Perform steps 3 to 7 on page 16, then startthe timer setting over.Press one of the TUNINGbuttons to display“EVERYDAY” or “ONCE”.UPDOWNTUNING34Press the MEMORY/SET button.• This sets the unit to the timersetting mode’s functionsetting mode.MEMORY/ SETExample: When the everyday timer isselected5Use the TUNING buttonsto switch the function to“TUNER”.UPDOWNTUNING✽ The function switches as follows each timethe button is pressed:: When the TUNING UP button is pressed.: When the TUNING DOWN button ispressed.6Press the MEMORY/SET button.• “TUNER” is stored in thememory as the timer function.MEMORY/ SETUse the TUNING buttonsto set preset number 3.UPDOWNTUNING78Press the MEMORY/SETbutton.• The preset station is stored inthe memory and the timer ontime setting mode is set.“E” and “oN” appearalternately in the display in thesteps 8 to 11.MEMORY/ SETtime>Use the tuning buttons to setthe hours position to “12”.9UPDOWNTUNING