Dension Smartlink MHL-9201-1 Install Manual
  | |
SmartlinkMHL, Video, BluetoothMHL-9201-1Install guide for SmartlinkMirroring Interface forBMW CIC & CCC1. IntroductionThe Smartlink from Dension is a vehicle and head unitspecific kit, giving you a brand new user experience on yoursmartphone with MHL connection. This cutting edge deviceallows you to see the exact same content on the car display as youhave on your phone and gives the possibility to control, browse,run applications, watch videos or play music from the connectedphone.Other devices like iPhone or iPod touch can also be connected tothe Smartlink (special adapter is required e.g. Lightning DigitalAV adapter for iPhone 5s / 5c /5) but without control option fromthe radio.Smartlink has one additional video input where external videocapable device(s) can be connected like a DVD player, rearviewcamera and many others with external video output.CompatibilityThe Smartlink is compatible with the following vehicles:Supported MHL capable phonesFor the latest compatibility please visit:http://www.mhlconsortium.org/productlist/mobile-devices/Please note: The MHL capable phones produced by SONY (e.g.:Xperia Z, T, etc.) are currently not supported by the Smartlink inCIC Professional system, since their video signal uses the NTSCstandard which is not available on CIC Professional systems.Important note for Samsung Galaxy S3/S4 users: Specialadapter is required for MHL functions. To be ordered separately(SML11SG).Supported iPod / iPhone devices1,2iPod Touch (2nd, 3rd or 4th generation)iPhone 5s / 5c / 5 / 4S / 4 / 3GS and 3G1 control is possible from the device user interface only2 additional Lightning or 30 pin Digital AV adapter is requiredPackage content• Smartlink interface• Single fibre optic cable kit• Specific car side harness• Connector Port• MHL cable (HDMI to Micro-USB)• Microphone• Instruction manuals (Install / User)Optional accessories• 5 pin to 11 pin adapter for Samsung (SML11SG)• RCA video cable (EXT1ICO)• GEN enabler tool (EN1VTBM)• HDMI Extension cable (EXTHDMI)2. Device InstallationThe Smartlink can be installed anywhere on the MOST ring,however in order to avoid any compatibility or functionalissues, please make sure that the Smartlink is the last connecteddevice on the MOST ring (Fig. 2). Please note: Installation of theSmartlink is very complex, therefore highly recommended tohave it installed by Professional Installer.Please note: Factory TV option has to be removed or looped iffitted because the Smartlink cannot retain this function.MOST ring installationDisconnect the fiber optic Male connector from the originalinterface (e.g. Head Unit) then remove the fiber optic housing fromthe Male connector and finally disconnect (Fig. 1.) the fiber opticfibre (the one which is marked to be the ‘signal in’ cable – withan arrow) as it is shown below:HU1a.Remove the blue locking clip from themiddle of the fibre optic housing.Strain the hook carefully with asharp tool, while pulling out theoptical fibre from the housing.1b.(Fig. 1)Connect that optical wire (use the optical male /male inlineconnector) with the ‘signal in’ cable of the Dension device.The optical fiber ‘signal out’ fibre of the Dension device mustbe connected to the original optic housing. Finally, take the Maleconnector and connect it to the original interface. At the end of theinstallation please make sure that the light directions of the MOSToptical ring are correct.3.Car side(Fig. 2)BMW E87, E90, E91, E92, E93, E60/61, E63/64and E70/71 with I-drive Professional (CIC, 8.8”dual slot)On the bottom of the Smartlink hardware, you will findconfiguration switches. Depending on your car make and radiotype you need to use different settings.Set the DIP switches on the hardwareHUBMWFirst carefully remove the Head Unit (radio) module from thedashboard as described in the factory instructions and using thecorrect tools.Model Head Unit Model YearBMW (E series)11, 3, 5, 6, X5 and X6I-Drive Professional(CCC, 8.8”, dual slot) 2004-2009BMW (E series)1, 3, 5, 6, X5 and X6I-Drive Professional(CIC, 8.8”, dual slot) 2009-20131 CCC Professional system with 7 buttons iDrive controller is currently not supportedSmartlink frontSmartlink backWith BMWs the iDrive control can be different depending on thebrowsing mechanism. You have a “Roll Over” type controller, ifyour iDrive can be rotated even if you have reached the last itemin the menu. You have a “Controlled” type if the iDrive joysticcannot be moved further after the last menu item. Please note:Press the reset button on the connector port or discconnect andreconnect the Smartlink hardware from power if you changed theDIP switch settings.BMW E87, E90, E91, E92, E93, E60/61, E63/64 andE70/71 with I-drive Professional (CCC, 8.8” dualslot) “Roll Over” typeBMW E87, E90, E91, E92, E93, E60/61, E63/64 andE70/71 with I-drive Professional (CCC, 8.8” dualslot) “Controlled” typeConnector Port USB HDMI Media PortMOST PowerVideoMIC RCPVersion 1.0 |
Related manuals for Dension Smartlink MHL-9201-1
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine