Desa B110BT Owner's Manual Manual pdf 7 page image
Manuals database logo
manualsdatabase
Your AI-powered manual search engine

Desa B110BT Owner's Manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 preview
Contents
  1. safety information
  2. product identification
  3. theory of operation
  4. to start heater
  5. troubleshooting
  6. service procedures
  7. fuel filter
  8. wiring diagram
  9. parts list
  10. replacement parts
  11. warranty and repair service
Desa B110BT Owner's Manual Manual pdf 7 page image
7104192OWNER’S MANUALFigure 7 - Pressure Gauge Plug RemovalFanMotorFigure 6 - Air Output, Air Intake, and LintFiltersFlushSetscrewMotorShaftFigure 5 - Fan Cross SectionSERVICEPROCEDURESWARNING: Never serviceheater while it is plugged in, op-erating, or hot. Severe burns andelectrical shock can occur.UPPER SHELL REMOVAL1. Remove screws along each side ofheater using 5/16" nut-driver. Thesescrews attach upper and lower shellstogether.2. Lift upper shell off.3. Remove fan guard.FANIMPORTANT: Remove fan from motor shaftbefore removing motor from heater. Theweight of the motor resting on the fan coulddamage the fan pitch.1. Remove upper shell (see above).2. Use 1/8" Allen wrench to loosen set-screw which holds fan to motor shaft.3. Slip fan off motor shaft.4. Clean fan using soft cloth moistenedwith kerosene or solvent.5. Dry fan thoroughly.6. Replace fan on motor shaft. Place fanhub flush with end of motor shaft (seeFigure 5).7. Place setscrew on flat of shaft. Tightensetscrew firmly (40-50 inch-pounds).8. Replace fan guard and upper shell.AIR OUTPUT, AIR INTAKE,AND LINT FILTERS1. Remove upper shell (see Upper ShellRemoval, column 1).2. Remove filter end cover screws using5/16" nut-driver.3. Remove filter end cover.4. Replace air output and lint filters.5. Wash or replace air intake filter (seePreventative Maintenance Schedule,page 5).6. Replace filter end cover.7. Replace fan guard and upper shell.IMPORTANT: Do not oil filters.PUMP PRESSUREADJUSTMENT1. Remove pressure gauge plug from filterend cover.2. Install accessory pressure gauge (partnumber HA1180).3. Start heater (see Operation, page 5).Allow motor to reach full speed.4. Using a flat blade screwdriver, adjustpressure. Turn relief valve to right toincrease the pressure. Turn relief valveto left to decrease the pressure. Setpump pressure at 5.3 PSI.5. Stop heater (see Operation, page 5).6. Remove pressure gauge. Replace pres-sure gauge plug in filter end cover.Figure 4 - Upper Shell RemovalUpperShell FanGuardFan GuardAir Intake FilterAir Output FilterFilter End CoverLint FilterReliefValvePressureGaugePlugPressureGaugeFigure 8 - Adjusting Pump PressureContinued
/ 16
Related manuals for Desa ARL B110BT
Desa B115T Owner's Manual first page preview
Desa B115T Owner's Manual
Desa B70D Owner's Manual first page preview
Desa B70D Owner's Manual
Desa B200 Owner's Manual first page preview
Desa B200 Owner's Manual
Desa B50H Owner's Manual first page preview
Desa B50H Owner's Manual
Desa B50G Owner's Manual first page preview
Desa B50G Owner's Manual
Desa 20 Owner's Manual first page preview
Desa 20 Owner's Manual
Desa 50 Owner's Manual first page preview
Desa 50 Owner's Manual
Desa 30 Owner's Manual first page preview
Desa 30 Owner's Manual
Desa BLP30 Owner's Manual first page preview
Desa BLP30 Owner's Manual
Desa B350D Owner's Manual first page preview
Desa B350D Owner's Manual
This manual is suitable for:
ARL B110BTARL R110BTARL REM110BTB110BTR110BT
Manuals database logo
manualsdatabase
Your AI-powered manual search engine