Desa CDCFTN Owner's Operation And Installation Manual

Also see for CDCFTN: OWNER'S OPERATION AND INSTALLATION MANUAL

Contents

Desa CDCFTN Owner's Operation And Installation Manual Manual pdf 22 page image

111244-01AFor more information, visit www.desatech.comFor more information, visit www.desatech.com22Figure 42- Setting the Selector Switch, Control Knob and FlameAdjustment Knob for Remote OperationREMOTEOFFON HILOINOUTFlameAdjustmentKnob Control KnobSelector Switch in RemotePosition (Optional RemoteControl)Shutting Off Fireplace1. Turn control knob clockwise to the OFF position.2. If Using Optional Hand-Held Remote: Set selector switchin the OFF position to prevent draining battery.Shutting Off Burners Only (pilot stays lit)You may shut off the burners and keep the pilot lit by doing oneof the following:1. Turn control knob clockwise to the PILOT position.2. If Using Optional Hand-Held Remote: Use remote con-trol manual OFF button.TO TURN OFF GASTO APPLIANCEOPERATING FIREPLACE (REMOTE-READY MODELS)To Turn Off Gas To ApplianceManual Lighting ProcedureOptional Hand-held Remote OperationOPERATING FIREPLACEContinuedMANUAL LIGHTINGPROCEDURE1. Follow steps 1 through 5 under Lighting Instructions, page 21.2. Depress control knob and light pilot with match.3. Keep control knob pressed in for 30 seconds after lightingpilot. After 30 seconds, release control knob. Now followsteps 8 and 9 under Lighting Instructions, page 21.WARNING: Make sure remote sensor selectorswitch is in the OFF position when you are away fromhome for long periods of time.Note: All remote control accessories must be purchased sepa-rately (see Accessories, pages 36 and 37). Follow instructionsincluded with the remote control.OPTIONAL HAND-HELDREMOTE OPERATIONNOTICE: You must light the pilot before using thehand-held remote control unit. SeeLighting Instruc-tions on page 21.1. After lighting, let pilot flame burn for about one minute.Turn control knob to ON position. Adjust flame adjustmentknob anywhere between HI and LO. Slide the selector switchto the REMOTE position (see Figure 42).Note: The burnermay light if hand-held remote was on when selector switchwas last turned off. You can now turn the burner on and offwith the hand-held remote control unit.IMPORTANT: Do not leave the selector switch in the RE-MOTE or ON position when the pilot is not lit. This willdrain the battery.Figure 43 - On/Off Hand-Held Remote Control Unit (GHRCB)Control ButtonTurns BurnersOn and OffON/OFF SERIES (MODEL [C]GHRCB)Hold the control button on the hand-held remote until burnerturns on. Hold the control button again until burner turns off(see Figure 43).TO LOCK press both buttons on hand-held remote control untillight stops flashing. Hand-held remote control is now locked. Ifthe fire is on it will be turned off automatically. In the lockedstate, the light will not light up when any button is pressed.TO UNLOCK press both buttons together on hand-held remotecontrol until the light stops flashing. The hand-held remote isnow unlocked.THERMOSTAT SERIES (MODEL [C]GHRCTB)The hand-held remote can be operated using either the manual mode(MANU) or thermostatic mode (AUTO) (see Figure 44, page 23). Toselect Fahrenheit/Centigrade mode display, carefully press the ˚C/˚Fmode button with the end of a paper clip or similar blunt object.Manual Mode1. Press the POWER and LOCK buttons together to turn onthe hand-held remote control.2. Press the MANU button to turn on the fireplace.3. Press the POWER and LOCK buttons together to turn offthe fireplace.Auto (Thermostatic) Mode1. Press the POWER and LOCK buttons together to turn onthe hand-held remote control.2. Press AUTO button to select this mode.3. Set the desired room temperature by pressing the TEMP+ or - buttons.4. Press the POWER and LOCK buttons together to turn offthe fireplace