www.desatech.com 116236-01A16CHECK GAS TYPEUse proper gas type for the fireplace unit you are installing. If you haveconflicting gas types, do not install fireplace. See retailer where youpurchased the fireplace for proper fireplace according to your gas typeor to purchase gas conversion kit (see Accessories, page 36).INSTALLING OPTIONAL BLOWERACCESSORIESNOTICE: If installing blower in an existing fireplacewith gas connections, shut off gas supply and dis-connect heater from gas supply. Contact a qualifiedservice person to do this.WARNING: If there is a duplex electrical outletinstalled in the right side of the bottom of the fireplacebase area, be sure that the electrical power to the outletis turned off before proceeding with blower installation.Failure to do this may result in serious injury..FIREPLACE INSTALLATIONModel BK InstallationFollow all instructions provided in the blower accessory kit.1. Attach the power cord to the blower motor by firmly pushing thetwo female terminals at the end of the power cord onto the twospade terminals on the blower motor (see Figure 25).2. Attach green ground wire from power cord to blower hous-ing using screw provided (see Figure 25). Tighten screwssecurely.3. Place the blower against the lower rear wall of the firebox outerwrapper with the exhaust port directed upward. The blower willfit inside the back opening and be held in position against theback wall by the magnets (see Figure 25).4. Be certain that all wire terminals are securely attached to ter-minals on blower motor and that the screw retaining the greenground wire is tight.Figure 25 - Blower Model BKMagneticStripsExhaust PortScrewGreen Ground WireSpade TerminalsSide ViewLower FireboxCavityBlowerLocationPARTS LIST FOR VENTING KITS ANDCOMPONENTSDESA (5"/8") Pipe & Vent KitsNumber DescriptionP58-6 6" Section Double Wall Pipe, GalvanizedP58-12 12" Section Double Wall Pipe, GalvanizedP58-24 24" Section Double Wall Pipe, GalvanizedP58-36 36" Section Double Wall Pipe, GalvanizedP58-48 48" Section Double Wall Pipe, GalvanizedPA58-712 Adjustable 7"-12" Section Double Wall Pipe,GalvanizedE58-45 45° Elbow, GalvanizedE58-90 90° Elbow, GalvanizedVKG-58 Ground Floor Vent Kit, Galvanized (Includes: 45° El-bow, 7"-12" Adjustable Pipe, Wall Firestop, HorizontalSquare Termination, 16 Screws)VKB-58 Basement Vent Kit, Galvanized (Includes: 45° Elbow,7"-12" Adjustable Pipe, Wall Firestop, HorizontalSquare Termination, 4' Pipe, 90° Elbow, 20 Screws)VKS-58 Snorkel Vent Kit, Galvanized (Includes: 45° Elbow,7"-12" Adjustable Pipe, Wall Firestop, 36" SnorkelTermination, 4' Pipe, 1' Pipe, 90° Elbow, 26 Screws)VKR-58 Roof Vent Kit, Galvanized (Includes: 45° Elbow, 7"-12"Adjustable Pipe, Flue Restrictor, Vertical High WindTermination, 2' Pipe, 4' Pipe, Wall Firestop, StormCollar, Roof Flashing [0/12 - 6/12], 26 Screws)VKC-58 Corner Vent Kit, Galvanized (Includes 45° Elbow,7"-12" Adjustable Pipe, Wall Firestop, HorizontalTermination, 6" Pipe, 90° Elbow, 18 Screws)HTK-58 Horizontal Round Termination Kit (Includes RoundTermination, Wall Firestop, 45° Elbow)HT-58 Horizontal Round Termination, GalvanizedHTS-58 Horizontal Square Termination, GalvanizedHTKS-58 Horizontal Square Termination Kit (Includes: SquareTermination, Wall Firestop, 45° Elbow)VT-58 Vertical Round Termination, GalvanizedST-58-14 14" Snorkel Termination, GalvanizedST-58-36 36" Snorkel Termination, GalvanizedSC-58 Storm Collar, GalvanizedWF-58 Wall Firestop, GalvanizedRF-58-6 Roof Flashing - 0 to 6/12 Pitch, GalvanizedRF-58-12 Roof Flashing - 6/12 to 12/12 Pitch, GalvanizedVR-58 Vertical Restrictor, GalvanizedS-58 Vinyl Siding Standoff, GalvanizedWS-58 Wall StrapCS-58 Cathedral Ceiling SupportFP-58 Firestop PlateSF-58 Stucco Flashing - For use with HTS-58VENTING INSTALLATIONINSTRUCTIONSContinuedVENTING INSTALLATION INSTRUCTIONSParts List for Venting Kits and ComponentsFIREPLACE INSTALLATIONCheck Gas TypeInstalling Optional Blower Accessories