Dynex DX-R27TV User Manual

Contents

Dynex DX-R27TV User Manual Manual pdf 9 page image

Setting up the television 9To select a setting using the TV buttons:• Use the CH and CH buttons and the VOL and VOLbuttons.To select a setting using the remote control:• Use the CH + and CH - buttons and the VOL + and VOL - buttons.Setting the languageYou can choose from three different languages (English, French, andSpanish) for the on-screen displays.To select a menu language:1 Press MENU/ENTER. The menu screen appears.Note:If no buttons are pressed for more than 60 seconds, the menu screen returnsto normal television operation automatically.2 Press the VOL + and VOL - buttons to select SETUP menu.3 Press the CH + and CH - buttons to select LANGUAGE, then pressthe VOL + button.4 Press the VOL + and VOL - buttons to select the desired language:• English (ENGLISH),• French (FRANÇAIS), or• Spanish (ESPAÑOL).5 Press EXIT to return to the normal screen.Memorizing channelsThis television is equipped with a channel memory feature which allowschannels to skip up or down to the next channel set into memory,skipping over unwanted channels. Before selecting channels, they mustbe programmed into the television’s memory.To use this television with an antenna, set the TV/CABLE menu option tothe TV mode. When shipped from the factory, this menu option is in theCABLE mode.Selecting TV or cableTo select TV or cable input:1 Press MENU/ENTER. The menu screen appears.2 Press the VOL + and VOL - buttons to select the SETUP menu.3 Press the CH + and CH - buttons to select TV/CABLE.4 Press the VOL + and VOL - buttons to select TV or CABLE.• TV—VHF/UHF channels• CABLE—Cable television channels5 Press EXIT to return to the normal screen.Note:It may take a few seconds for a digital channel picture to appear on screenafter being selected.CABLE CHARTThe following chart is typical of many cable system channel allocations.The number on the top is the number on the television. The number orletter on the bottom is the corresponding cable channel.Automatic memory tuningMemorizing channels is best accomplished during evening “primetime”hours, as more channels are broadcasting digital signals. Memorizingchannels can only be accomplished while a station is broadcasting adigital signal to set the channel into memory.If you are not sure of the digital channels available in your area, visitwww.antennaweb.org to find a list based on your address or zip code.To automatically memorize channels:1 Press MENU/ENTER. The menu screen appears.2 Press the VOL + and VOL - buttons to select the SETUP menu,then press the CH + and CH - buttons to select AUTO CHMEMORY.3 Press the VOL + button. The television begins memorizing all ofthe channels available in your area.After completing analog tuning, digital tuning startsautomatically. Depending on the reception condition, it may takefrom 15 to 30 minutes to complete memorizing digital cablechannels. Depending on the condition of the reception, the BARdisplay may not advance for several minutes.Note:Some new channels may be added. You should complete the AUTO CHMEMORY procedure periodically.Adding and deleting channelsTo add or delete analog channels:1 Press TUNER to select the Analog mode.2 Press MENU/ENTER. The menu screen appears.3 Press the VOL + and VOL - buttons to select the OPTION menu,then press the CH + and CH - buttons to select ADD/DELETE.4 Press the VOL + button. The ADD/DELETE menu appears.5 Select the desired channel to be memorized or deleted using theCH + and CH - buttons.6 Press the VOL + and VOL - buttons to select ADD or DELETE.7 Repeat steps 5-6 for other channels you want to add or delete.8 Press EXIT to return to the normal screen.To add or delete digital channels:1 Press TUNER to select the Digital mode.2 Press MENU/ENTER. The menu screen appears.3 Press the VOL + and VOL - buttons to select the OPTION menu,then press the CH + and CH - buttons to select DIGITAL SETUP.4 Press the VOL + button. The DIGITAL SETUP menu appears.5 Press the CH + and CH - buttons to select ADD/DELETE, thenpress the VOL + button. The ADD/DELETE (DTV) menu appears.6 Press the CH + and CH - buttons to select ADD/DELETE, thenpress the VOL + button.7 Select the desired channel to be memorized or deleted using theCH + and CH - buttons.8 Press the VOL + and VOL - buttons to select ADD or DELETE.9 Repeat steps 6-8 for other channels you want to add or delete,then press MENU/ENTER.10 Press MENU/ENTER repeatedly to return to the normal screen.To add a digital channel you are watching:1 Press TUNER to select the Digital mode. Use the number buttonsto directly select the digital channel you want to add.2 Press MENU/ENTER. The menu screen appears.3 Press the VOL + and VOL - buttons to select the OPTION menu,then press the CH + and CH - buttons to select DIGITAL SETUP.4 Press the VOL - button. The DIGITAL SETUP menu appears.5 Press the CH + and CH - buttons to select ADD/DELETE, thenpress the VOL - button. The ADD/DELETE (DTV) menu appears.6 Press the CH + and CH - buttons to select ADDING CHANNEL,then the VOL + button.7 Press MENU/ENTER repeatedly to return to the normal screen.8 Repeat steps 1-7 for other channels you want to add directly.