Dyson AM10 Operating Manual
Also see for AM10: Operating manualOperating manualOperating manualOperating manualOperating manual
                    | |
Using your humidifierPlease read the ‘Important Safety Instructions’ in this Dyson OperatingManual before proceeding.Introduction• This is a cool mist, ultrasonic type of humidifier. Moist air isdirected into the room from the loop amplifier.• Water passes over a UV-C emitter to ensure that it is 99.9%bacteria-free before misting commences.Location• Always place the appliance on a firm, flat, level surface.• Do not place the appliance on a rug, carpet, wooden flooring, orany other surface that may be damaged by exposure to water ormoisture.• It is recommended that a waterproof mat or pad is placed underthe appliance.• Do not place the appliance underneath overhanging surfaces.• Do not place the appliance in an area where it is accessible tochildren.• Store the appliance indoors. Do not use or store it below 5°C(41°F). Ensure the appliance is at room temperature beforeoperating.• For the best performance, place on the floor, in the corner of theroom, at least 1m from any wall and facing into the centre of theroom.Operation• All parts must be securely fitted before use.• Do not use the appliance unless it has been cleaned according toinstructions.• In humidifier mode do not use without water in the tank.• Do not lubricate any part of this appliance.• When switched on, a small blue LED on the back of the appliancelights up to show that power is being received by the appliance.(Note: It does not mean that the appliance itself is operating.)• Once the water treatment cycle completes the appliance is readyto begin humidification.Setting humidity level• On first use, the display will show ‘70%’, which is the highestrelative humidity setting. The fan will run on lowest airspeed, ‘01’.For each use after this the appliance will remember the last targethumidity level and airflow speed set.• The appliance will not operate unless the target humidity setting isabove the current room humidity level.• The appliance will automatically adjust to avoid excessivehumidity.• Mist will be visible only in certain conditions (impacted by light,background colour, etc.) or at the lowest settings.Automatic mode• Press the AUTO button on the remote. This is the recommendedmode of operation.• The appliance selects a comfortable humidity for the room, basedon environmental factors such as current humidity level and airtemperature.• When the room reaches the appropriate humidity level theappliance will switch itself ‘ON’ or ‘OFF’ as necessary to maintainthat level. The fan will remain running when the target humidityhas been reached.Manual mode• Select the desired humidity level (from 30% to 70%). When theroom reaches the target humidity level the appliance will switchitself ‘ON’ or ‘OFF’ as necessary to maintain that level. The fanwill remain running when the target humidity has been reached.Fan mode• The fan mode button on the remote control turns the humidifiermode ‘OFF’. Control the fan mode using the airflow and timerbuttons.• No water is needed for the fan mode.Control without the remote• Press the Standby button on the appliance to turn ON/OFF.• Press and hold the power button on the appliance to adjust thehumidity setting.• Fan mode and the sleep timer cannot be operated without theremote control.• The air speed setting automatically sets to '05'.Refilling• When refilling, empty the tank completely (preferably washingand drying it), then refill – this keeps the water fresh.• With a full tank of cold tap water (3 litres) the appliance will runfor at least 10 hours, depending on the target humidity settingand other environmental conditions. Do not add anything to thewater (such as scents, oils etc).Cleaning the base• Small water spillages may occur. While the amount of water inthe trough is not significant enough to damage the appliance,significant care should be taken when emptying it. Ensure thatwater does not enter through the inlets of the appliance. If somewater does pass through the inlets, dry the exterior with a clothand continue to use as normal.Cleaning the tank• Pour in the recommended citric acid solution. Replace the capand shake tank for 30 seconds. Then leave to stand. After 15minutes, empty the tank. Rinse and wipe over all surfaces. Repeatif necessary.Storage• When not in use, unplug from the mains electricity supply.• Store the appliance in a dry location and arrange the cable awayfrom traffic areas so that it will not be tripped over or damaged.• Clean the appliance and tank as instructed before storing andbefore re-use.Battery replacementCAUTION• Unscrew the battery compartment on the remote control. Loosenthe base and pull to remove the battery.• Do not install backwards or short circuit the batteries.15 |
Related manuals for Dyson AM10
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine