Eaton Cooper Power Series Installation Instructions Manual

Also see for COOPER POWER SERIES: Installation and operation instructions Installation instructions Installation instructions Installation and operation instructions Operation instructions

Contents

Eaton Cooper Power Series Installation Instructions Manual Manual pdf 4 page image

iv15, 25, and, 35kV Cleer BailInstallatIon InstructIons MN650064EN August 2018Safety for lifeEaton meets or exceeds all applicable industry standards relating to product safety in its Cooper Power™ series products.We actively promote safe practices in the use and maintenance of our products through our service literature, instructionaltraining programs, and the continuous efforts of all Eaton employees involved in product design, manufacture, marketing, andservice.We strongly urge that you always follow all locally-approved safety procedures and safety instructions when working aroundhigh-voltage lines and equipment, and support our “Safety For Life” mission.Safety informationThe instructions in this manual are not intended as asubstitute for proper training or adequate experience in thesafe operation of the equipment described. Only competenttechnicians who are familiar with this equipment shouldinstall, operate, and service it.A competent technician has these qualifications:●● Is thoroughly familiar with these instructions.●● Is trained in industry-accepted high- and low-voltage safeoperating practices and procedures.●● Is trained and authorized to energize, de-energize, clear,and ground power distribution equipment.●● Is trained in the care and use of protective equipmentsuch as arc flash clothing, safety glasses, face shield,hard hat, rubber gloves, clampstick, hotstick, etc.Following is important safety information. For safeinstallation and operation of this equipment, be sure to readand understand all cautions and warnings.Hazard Statement DefinitionsThis manual may contain four types of hazard statements:DANGERIndicates an imminently hazardous situation which, ifnot avoided, will result in death or serious injuryWARNINGIndicates a potentially hazardous situation which, if notavoided, could result in death or serious injuryCAUTIONIndicates a potentially hazardous situation which, if notavoided, may result in minor or moderate injuryNOTICEIndicates a potentially hazardous situation which, if notavoided, may result in equipment damage onlySafety instructionsFollowing are general caution and warning statements thatapply to this equipment. Additional statements, related tospecific tasks and procedures, are located throughout themanual.DANGERHazardous voltage Contact with hazardous voltage willcause death or severe personal injury Follow all locally-approved safety procedures when working around high-and low-voltage lines and equipment G103 3WARNINGBefore installing, operating, maintaining, or testing thisequipment, carefully read and understand the contentsof this manual Improper operation, handling, ormaintenance can result in death, severe personal injury,and equipment damage G101 0WARNINGThis equipment is not intended to protect humanlife Follow all locally-approved procedures and safetypractices when installing or operating this equipmentFailure to comply can result in death, severe personalinjury, and equipment damage G102 1WARNINGPower distribution and transmission equipment mustbe properly selected for the intended application Itmust be installed and serviced by competent personnelwho have been trained and understand proper safetyprocedures These instructions are written for suchpersonnel and are not a substitute for adequate trainingand experience in safety procedures Failure to properlyselect, install, or maintain power distribution andtransmission equipment can result in death, severepersonal injury, and equipment damage G122 2WARNINGCLEERBAIL and CLEERCHAIN are required when aCleer 4/0 grounding elbow (GE6354) is mated with aCleer Insert (LBI635) on a 35kV Tee (DT635) in locationswhere available fault currents are in excess of 16kARMS symmetrical to 25kA RMS symmetrical TheCLEERCHAIN and CLEERBAIL work together to securelyhold the grounding elbow on the bushing during amomentary through faultCAUTIONThe Eaton Cooper Power series 600 A Cleer GroundedElbow is designed to be operated in accordance withnormal safe operating procedures These instructions arenot intended to supersede or replace existing safety andoperating procedures The grounding elbow should beinstalled and service only by personnel knowledgeableof good safety practices and fully trained on theinstallation and application of high voltage electricalequipment For product applications that require ratingsor characteristics not shown, contact Eaton for specificrecommendations!SAFETYFOR LIFE!SAFETYFOR LIFE