UPS MAINTENANCEEATON Powerware® 9125 Two-in-One UPS (700–2000 VA) User’s Guide S 164201514 Rev B www.powerware.com 49How to Replace Internal BatteriesC A U T I O NPull the battery out onto a flat, stable surface. The battery is unsupported when you pull itout of the UPS.To replace the UPS internal batteries:1. Remove the UPS front cover (see Figure 29).NOTE DO NOT attempt to open the left side.Figure 29. Removing the UPS Front Cover2. Unscrew and set aside the battery retaining bracket (see Figure 30).3. Disconnect the battery cable from the UPS battery connector andremove the battery cable from the wire clips.Battery Retaining BracketWire ClipsBatteryConnectorFigure 30. Accessing the UPS Internal Battery

Eaton Powerware 9125 Manual

Restriction of Hazardous Substances Directive

Risk Protection as Easy as 3, 5, 9

Power Problems and Their UPS Solutions

Which UPS is Right for Your Customer

ABM ® Technology

What's the Harm in Harmonics

Series 9 and Ferro UPSs Address Harmonics

Single-phase Powerware Product Warranty Overview

Powerware Enclosures

Powerware Enclosure Power Distribution Unit (ePDU™)

Powerware Environmental Rack Monitor (ERM)

Powerware Remote Power Panel (RPP)

UL Listed Power Distribution Cables

Powerware 3105

Powerware 5110

service plans

Powerware 5115 Rack

Powerware 5125 Tower

Powerware 9120

Powerware 9140

Powerware 9155

Powerware 9170+ Rack/Tower

Powerware FERRUPS ® FE 60 Hz

Powerware FERRUPS Rack Series

Powerware FERRUPS External Options & Accessories

Powerware 9355 (10–15 kVA)

Powerware 9355 (20–30 kVA)

Software Products

Connectivity Products

connectivity options

Residential Surge Products

Portable Generators

surge protection

Data Line and Telecommunication

Powerware Product Services

battery replacement

Powerware Three-phase UPS Batteries

Input Plug and Output Receptacle Chart

Powerware 9125

Introduction

Safety Warnings

belangrijke veiligheidsinstructies

tarkeita turvaohjeita

avvisi di sicurezza

viktig sikkerhetsinformasion

advertencias de seguridad

Installation

Installing the UPS Internal Batteries

Tower Setup

EBM Installation

Plug-Receptacle UPS Installation

Remote Emergency Power-off Installation

Hardwired UPS Installation

Operation

Turning the UPS Off

Transferring the UPS to Bypass Mode

Normal Mode

Battery Mode

Bypass Mode

Configuration

Communication

DB-9 Communication Port

X-Slot Cards

UPS Maintenance

Replacing Batteries

How to Replace Internal Batteries

Testing New Batteries

Recycling the Used Battery or UPS

Specifications

Troubleshooting

Service and Support

Warranty

Ten-Year Pro-Rated Limited Warranty (US and Canada)

Load Protection Guarantee (US and Canada)

Connecting the UPS Internal Battery

Rack-Mount Setup

Extended Battery Module Installation

UPS Rear Panels

Operating Modes

Additional UPS Features

Single-Port Card

Network Transient Protector

Load Segments

When to Replace Batteries

How to Replace UPS Internal Batteries

How to Replace Extended Battery Modules

UPS Setup

Installing the UPS

USB Card

special symbols

UPS Internal Battery Connection

Setup and Installation

UPS Monitoring

Connexion à la Batterie Interne de l'Onduleur

Configuration et Installation

Configuration en tour

Installation de l'onduleur

Surveillance de l'onduleur

Panneaux arrières de l'onduleur

Service après-vente et assistance technique

Einbau

Interner USV-Batterieanschluss

Montage und Installation

Montage im Tower

Installieren der USV

USV-Überwachung

Rückwände der USV

Kundendienst und Unterstützung

Installazione

Collegamento Batteria Interna UPS

Approntamento e Installazione

Approntamento tower

Installazione della UPS

Monitoraggio UPS

Pannelli posteriori UPS

Assistenza e supporto

Instalación

Conexión de la Batería Interna del SIE

Configuración e Instalación

Configuración de la torre

Instalación del SIE

Control del SIE

Paneles posteriores del SIE

Servicio y soporte

important safety instructions

UPS Shutdown

Hardwired PDM Installation

Plug-Receptacle PDM Installation

Plug-Receptacle PDM Rear Panels

PDM Schematics

PDM Installation

UPS Installation

Power Connections and Startup

Typical Power Connections

Configuration Mode

Communication Options

i5, iSeries, or AS/400 and Serial Server Interface Overview

Serial (TTY) Interface Overview

p5 or pSeries with Logical Partitions Interface Overview

Applications S 164201696 Rev

i5 Interface Overview

iSeries or AS/400 Interface Overview

Configuration en Tour

Installation d'un EBM

Installation d'un PDM

Installation de l'Onduleur

Installation de Arrêt d'Urgence à Distance

Connexions Électriques et Mise en Marche

Connexions Électriques Type

Segments de Charge

Fonctionnement

Mise Hors Tension de l'Onduleur

Modes de Fonctionnement

Mode Normal

Mode Batterie

Mode Dérivation

Options de Communication

Aperçu de l'Interface i5

Aperçu de l'Interface iSeries ou AS/400

Aperçu de l'Interface Série (TTY)

Aperçu de l'Interface des Serveurs p5 ou pSeries avec Partitions Logiques

Entretien et Assistance

Einbau des EBM

Einbau des PDM

USV-Installation

Fern-Notausschaltung-Installation

Stromanschlüsse und Hochfahren

Typische Netzanschlüsse

Lastsegmente

Betrieb

Ausschalten der USV

Betriebsarten

Normalbetrieb

Akkubetrieb

Bypassbetrieb

Konfigurationsbetrieb

Kommunikation

Kommunikationsoptionen

i5 Schnittstellenüberblick

Überblick über die Schnittstelle, iSeries oder AS/400

Übersicht über die Serielle (TTY) Schnittstelle

p5 oder pSeries mit Überblick über die Schnittstelle mit den Logischen Partitionen