Fein ASCS4.8 User Manual
Also see for ASCS4.8: Instruction manual
                                                                                                                             | |
Contents | 
18 enHand/arm vibrationsThe vibration emission level given in this informationsheet has been measured in accordance with a standard-ised test given in EN 60745 and may be used to compareone tool with another. It may be used for a preliminaryassessment of exposure.The declared vibration emission level represents themain applications of the tool. However, if the tool is usedfor different applications, with different accessories orpoorly maintained, the vibration emission may differ.This may significantly increase the exposure level overthe total working period.An estimation of the level of exposure to vibrationshould also take into account the times when the tool isswitched off or when it is running but not actually doingthe job. This may significantly reduce the exposure levelover the total working period.Identify additional safety measures to protect the opera-tor from the effects of vibration such as: maintain the tooland the accessories, keep the hands warm, organisationof work patterns.Operating instructions.Adjust the rotation selector switch only when themachine is at a complete stop.To avoid accidental starting, e. g., during transport, setthe rotation selector switch to the centre position.When overheated, the machine runs with short, low-power impulses. Allow the machine to cool down at no-load speed.For reliable working results, always carry out screwdriv-ing operations using the depth stop.Electronic torque shut-off (see pages 6 – 7).The electronic torque shut-off can be used when workingwithout depth stop.Adjust the torque only when the machine is at a completestop.The motor switches off when reaching the set torque andan audio signal sounds. After the shut-off has taken place,release the on/off switch and press it again for the nextscrewdriving operation.The audio signal can be switched on and off.The electronic shut-off is deactivated when working inthe “ ” torque level.To achieve good working results, press the power toolwith sufficient force against the screw.Handling the battery.Operate and charge the battery only within the batteryoperating-temperature range of 0 °C – 45 °C (32 °F –113 °F). At the beginning of the charging procedure, thebattery temperature must be within the battery operat-ing-temperature range.The real percentage of the battery charge condition isonly indicated when the power tool motor is stopped.The electronics automatically switch off the motor priorto the battery being deep discharged.Repair and customer service.When working metal under extreme operat-ing conditions, it is possible for conductivedust to settle in the interior of the power tool.Blow out the interior of the power tool via the ventila-tion slots frequently with dry and oil-free compressed air.If required, you can change the following parts yourself:application tools, depth stop, battery, belt clipWarranty and liability.The warranty for the product is valid in accordance withthe legal regulations in the country where it is marketed.In addition, FEIN also provides a guarantee in accordancewith the FEIN manufacturer’s warranty declaration.The delivery scope of your power tool may include onlya part of the accessories described or shown in thisInstruction Manual.Declaration of conformity.FEIN declares itself solely responsible for this productconforming with the relevant provisions given on the lastpage of this Instruction Manual.Technical documents at: C. & E. FEIN GmbH, EGZ,D-73529 Schwäbisch GmündEnvironmental protection, disposal.Packaging, worn out power tools and accessories shouldbe sorted for environmental-friendly recycling.Dispose of batteries only when discharged.For batteries that are not completely discharged, insulatethe terminals with tape as a protective measure againstshort-circuiting.LED indicator Meaning Activity1 – 4 greenLEDPercentage ofcharge conditionOperationContinuousred lightBattery is almostemptyCharge batteryRed flashinglightBattery is notready for opera-tionBring the battery intothe battery operat-ing-temperaturerange, then chargeOBJ_BUCH-0000000042-001.book Page 18 Wednesday, October 19, 2011 8:35 AM |
Related manuals for Fein ASCS4.8
manualsdatabase
Your AI-powered manual search engine