GE GFDN110ED Dimensions And Installation Information

Contents

GE GFDN110ED Dimensions And Installation Information Manual pdf 3 page image

Special inStallation RequiRementSSpecification Revised 10/15GFDn110eDGE® Series 7.0 Cu. Ft. Super Capacity Front Load Electric DryerFor answers to your Monogram, GE Profile™ Seriesor GE ® Series appliance questions, visit our websiteat geappliances.com or call GE Answer Center ®service, 800.626.2000.Dryer exhausting information – Metal duct only.For complete information, see installation instructions packed with your dryer.Ducting materials: For best performance, this dryer should be vented with 4" diameterall rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal(semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessaryto connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexiblemetal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal(semi-rigid) ducting cannot be used AND where a 4" diameter can be maintained throughout theentire length of the transition duct. Please see installation instruction packed with your dryer forcomplete instructions when using flexible metal (foil type) ducting.exhaust length calculation:1. Determine the number of 90° turns needed for your installation. If you exhaust to theside or bottom of dryer, add one turn.2. The maximum length of 4' rigid (aluminum or galvanized) duct which can be tolerated isshown in the table.A turn of 45° or less may be ignored. Two 45° turns within the duct length should betreated as a 90° elbow.A turn over 45° should be treated as a 90° elbow.Dryers must be exhausted to the outside.caution: For personal safety do not terminate exhaust into a chimney, under any enclosed housefloor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisturecould cause damage. Never terminate the exhaust into a common duct or plenum with a kitchenexhaust, since the combination of lint and grease could create a fire hazard.Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc.The wall cap must also be located at least 12" above the ground or any other obstruction with theopening pointed down.for more information on venting kits anD accessories, please call1-800-ge-cares.Best performanceMaximum lengthof 4" dia rigidmetal ductExhaust hood typeDomestic dryer modelsNumberof 90°turnsa4"openingB2-1/2"openingGE Front Load Long Vent 7.0cu. ft. capacity electric dryer(GFDL)0 200 ft. 175 ft.1 185 ft. 165 ft.2 175 ft. 155 ft.3 165 ft. 145 ft.4 155 ft. 135 ft.5 145 ft. 125 ft.Long Vent 6.0 - 8.0 cu. ft.capacity electric & gas dryers(GTDL and GTV)0 150 ft. 125 ft.1 135 ft. 115 ft.2 125 ft. 105 ft.3 115 ft. 95 ft.4 105 ft. 85 ft.5 95 ft. 75 ft.Long Vent 7.0 cu. ft. capacityelectric & gas (GTD42, GTD45,GTD65, GTX42 and GTX60)0 120 ft. 90 ft.1 100 ft. 75 ft.2 85 ft. 65 ft.3 70 ft. 55 ft.4 60 ft. 45 ft.5 55 ft. 35 ft.All 6.0 - 8.3 cu. ft. capacitymodels electric and gas dryers(GFDS, GFDR, GFDN, GTDS,GTDN, GHDN, GHDS, GTDP,GLDP, GTD, HTDP, HTDX)0 90 ft. 60 ft.1 60 ft. 45 ft.2 45 ft. 35 ft.3 35 ft. 25 ft.4 25 ft. 15 ft.DCVH4800 90 ft. 60 ft.1 60 ft. 45 ft.2 45 ft. 35 ft.3 35 ft. 25 ft.All 3.6 cu. ft. (DSKS, DSKP)electric dryers0 46 ft. 37 ft.1 37 ft. 30 ft.2 30 ft. 22 ft.3 23 ft. 15 ft.Laundry Center GUD270 56 ft. 42 ft.1 48 ft. 34 ft.2 40 ft. 26 ft.3 32 ft. 18 ft.Laundry Center GUD240 43 ft. 36 ft.1 33 ft. 26 ft.2 24 ft. 16 ft.AB2-1/24GE Dryer VentAB2-1/24GE Dryer VentADryer exhausting information—use metalDuct only vertical anD horizontal DuctingListed byUnderwritersLaboratories

/ 4

Related manuals for GE GFDN110ED