GE GXULQ Installation Instructions Manual

Also see for GNULQ: Installation instructions

Contents

INSTALL COMPRESSION FITTINGSTake the remaining section of tubing, slide the compressionhex nut and 3/8” ferrule (tapered end away from thecompression nut) onto the tubing, and put in the tube insert.Fasten the assembly onto the cold water supply valve.Do not overtighten.NOTE: Overtightening will cause the tubing to separate fromthe fitting.NOTE: For shut-off valves with 1/2” or 7/16” compressionfittings, please use appropriate adapters provided in the kit.Connect the other end to the inlet side as indicatedby the arrow on the filter head/bracket.CAB7• What does this warranty cover?— Any defect in materials or workmanship in the manufactured product.• What does this warranty not cover?— Filter cartridge and batteries after 30 days from date of purchase.— Service trips to your home to teach you how to use the product.— Improper installation, delivery or maintenance.— Failure of the product if it is abused, misused, altered, used commercially or usedfor other than the intended purpose.— Use of this product where water is microbiologically unsafe or of unknown quality,without adequate disinfection before or after the system. Systems certified for cystreduction may be used on disinfected water that may contain filterable cysts.— Damage to the product caused by accident, fire, floods or acts of God.— Incidental or consequential damage caused by possible defects with thisappliance, its installation or repair.• For how long after the original purchase?— One (1) year.• How do I make a warranty claim?— Return to the retailer from which it was purchased, along with a copy of the “Proofof Purchase.” A new or reconditioned unit will be provided. This warranty excludesthe cost of shipping the product to your home.This warranty is extended to the original purchaser and any succeeding owner forproducts purchased for home or office use within the USA. In Alaska, the warrantyexcludes the cost of shipping or service to your home or office.Some states do not allow the exclusion or limitation of incidental or consequentialdamages. This warranty gives you specific legal rights, and you may also have otherrights, which vary from state to state. To know what your legal rights are, consultyour local or state consumer affairs office or your state’s Attorney General.Contact us at ge.com, or call toll-free at 800.952.5039 in the U.S., or 866.777.7627 in Canada.Installation InstructionsFINAL CHECKInsert the filter into the filter head/bracket. Turnthe filter 1/4 turn to the right until it stops. Thetop surface of the filter will become flush withthe bottom of the filter head/bracket when it isfully installed.Slowly turn on the water supply.Check the entire system for leaks. If there areleaks, refer back to the Cut the Tubing sectionto reinsert the tubing.If leaking from fittings, shut off water pressureand tighten or reseal fittings. If leaking from thefilter, tighten the filter.After installation, let water run for approximately5 minutes to flush the filter and to remove air.NOTE: It is normal for there to be air in thesystem causing bubbles in the water.EDCBA9PARTS LISTRef. No. Part No. Part Description001 GXULQR Replacement Filter Cartridge 1002 WS19X10024 Filter Head/Bracket 1003 GXULQ-KIT Kit 1004 GXULQ-TIMER Timer and Batteries 1To obtain replacement parts, call toll-free 800.626.2002 (U.S.),800.663.6060 (Canada–English), 800.361.3869 (Canada–French).GE Consumer & IndustrialAppliancesGeneral Electric CompanyLouisville, KY 40225003004001LIMITED ONE YEAR WARRANTYEXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy isproduct exchange as provided in this Limited Warranty. Any implied warranties,including the implied warranties of merchantability or fitness for a particularpurpose, are limited to one year or the shortest period allowed by law.4002Shut-Off Valve Tubing Insert Ferrule Hex Nut TubingShut-Off Valve Tubing Insert Ferrule Hex Nut TubingINSTALL THE BATTERIESInsert coin or screwdriver in the slotbetween the timer cap and base.Gently pry open and separate thetimer base from the cap. Install orchange 2 new AAA 1.5 volt batteries.After having the batteries in place,line up the base and cap and snapthem back together.After new batteries are installed orfilter is changed, push and hold the timer blue reset buttonfor approximately 5 seconds. Release the reset buttonafter the light flashes 5 times. The light will flash againin 180 days to remind you that it is time to change the filter.Attach timer to remote location for easy viewing.NOTE: Do not mix old and new batteries. Do not mix alkaline,standard (carbon-zinc) or rechargeable (ni-cad, ni-mh, etc.)batteries.DCBA8TimerCapTimerBase2 AAABatteriesBlue Reset ButtonNOTE: Timerappearance may vary.