GE JCBP24, JCBP25, JCBP26, JCBP27, JCBP28, JCBP29, JCBP30, JCBP32, JCBP33, JCBP34, RCB735, RCB740, RCB745, RCB746, RCB790 Installation And Owner's Instructions

Also see for JCBP24: Owner's manual Owner's manual

GE JCBP24, JCBP25, JCBP26, JCBP27, JCBP28, JCBP29, JCBP30, JCBP32, JCBP33, JCBP34, RCB735, RCB740, RCB745, RCB746, RCB790 Installation And Owner's Instructions Manual pdf 32 page image

Installation Instructions RangeIf you have questions, call 1.800.GE.CARES or visit our Website at: ge.comBEFORE YOU BEGINRead these instructions completely and carefully.Installation of this range must conform with localcodes, or in the absence of local codes, with theNational Fuel Gas Code, ANSI Z223.1/NFPA.54,latest edition. In Canada, installation must conformwith the current Natural Gas Installation Code,CAN/CGA-B149.1 or the current Propane InstallationCode, CAN/CGA-B149.2, and with local codes whereapplicable. This range has been design-certified byCSA International according to ANSI Z21.1, latestedition and Canadian Gas Association according toCAN/CGA-1.1 latest edition.As with any appliance using gas and generating heat,there are certain safety precautions you should follow.You will find these precautions in the Important SafetyInformation section in the front of this manual. Readthem carefully.• IMPORTANT – Save these instructionsfor local electrical inspector’s use.• IMPORTANT – Observe all governingcodes and ordinances.• Note to Installer – Be sure to leave theseinstructions with the Consumer.• Note to Consumer – Keep these instructions forfuture reference.• Note – This appliance must be properly grounded.• Servicer – The electrical diagram is in an envelopeattached to the back of the range.• Skill level – Installation of this appliance requires basicmechanical skills.• Proper installation is the responsibility of the installer.• Product failure due to improper installation is notcovered under the Warranty.FOR YOUR SAFETYDo not store or use combustible materials, gasoline orother flammable vapors and liquids in the vicinity of thisor any other appliance.If you smell gas:Open windows.Don’t touch electrical switches.Extinguish any open flame.Immediately call your gas supplier.TOOLS YOU WILL NEEDMATERIALS YOU MAY NEED• Gas line shut-off valve.• Pipe joint sealant or UL-approved pipe thread tapewith Teflon* that resists action of natural and LP gases.• Flexible metal appliance connector (1/2 ″ I.D.)A 5-foot length is recommended for ease of installationbut other lengths are acceptable. Never use an oldconnector when installing a new range.• Flare union adapter for connection to gas supply line(3/4 ″ or 1/2 ″ NPT x 1/2 ″ I.D.)• Flare union adapter for connection to pressureregulator on range (1/2 ″ NPT x 1/2 ″ I.D.)• Liquid leak detector or soapy water.• Lag bolt or 1/2″ O.D. sleeve anchor (for concretefloors only).*Teflon: Registered trademark of DuPontFlat-blade screwdriverPipe wrenches (2)(one for backup)Phillips screwdriverOpen-end oradjustable wrenchPencil and rulerLevelIn the Commonwealth of Massachusetts:• This product must be installed by a licensed plumberor gas fitter.• When using ball-type gas shut-off valves, they shall bethe T-handle type.• A flexible gas connector, when used, must not exceed3 feet.Drill, awl or nailPART INCLUDEDAnti-Tip bracket kit 32