GE JSP39SNSS Dimensions And Installation Information

GE JSP39SNSS Dimensions And Installation Information Manual pdf 1 page image

For answers to your Monogram,® GE Profile™ orGE® appliance questions, visit our website atge.com or call GE Answer Center ® service,800.626.2000.All GE ranges are equipped withan Anti-Tip device. The installationof this device is an important,required step in the installationof the range.Listed byUnderwritersLaboratoriesDimension and installation information are shown in inches.Dimensions and Installation Information (in inches)JSP39SNGE® 30" Slide-In Electric Range with Self-Cleaning OvenSpecification Revised 6/10320643KW Rating240V 11.9208V 8.9If you are NOT using theoptional Filler or Backguard:23-3/1630If you are using the optionalFiller or Backguard:2530If you are NOT using theoptional Filler or Backguard:23-3/1630If you are using the optionalFiller or Backguard:2530AcceptableElectricalOutlet Area30" Min.30" Min.Shave Raised Edge To Clear31-1/8" Wide Control PanelExcluding Models JSS28 and JSP392-7/8"To FrontSurface OfCountertop20-5/8" DoorClearanceFrom FrontSurface ofCountertop31-1/43025-3/4**Recommended6" Min.From Walls23-3/1615" Min.A/B*13" Max.2-1/230259/167-1/22-1/2AccessoryBackguard2436-1/4*JXS37 is 5-1/4" and J(excluding handle) **Total depth from wallfront of closed oven dincluding handle is 2735-7/8"–38"from floor tocountertopIf the countertop area is not flat, excess tension may be applied to the glass cooktop causing breakageand voiding the warranty. Make sure the wall covering, countertop, flooring and cabinets around the rangecan withstand the heat (up to 200°F) generated by the range.A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or metal cabinet,or allow a 24" minimum when bottom of wood or metal cabinet is protected by no less than 1/4"-thickflame-retardant millboard covered with no less than No. 28 MSG sheet metal (.015" thick), .015"-thickstainless steel, .025" aluminum or .020" copper.B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop. However,a minimum 6" spacing to surfaces less than 15" above the cooktop and adjacent cabinetry isrecommended to reduce exposure to steam, grease splatter and heat. Allow 1/4" minimum clearanceat the back wall.To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space abovethe cooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk canbe reduced by installing a range hood that projects at least 5" beyond the front of the cabinets. Cabinetsinstalled above the cooktop must be no deeper than 13".AcceptableElectricalOutlet Area30" Min.30" Min.Shave Raised Edge To Clear31-1/8" Wide Control PanelExcluding Models JSS28 and JSP392-7/8"To FrontSurface OfCountertop20-5/8" DoorClearanceFrom FrontSurface ofCountertop31-1/43025-3/4**Recommended6" Min.From Walls23-3/1615" Min.A/B*13" Max.2-1/230259/167-1/22-1/2AccessoryBackguard2436-1/4*JXS37 is 5-1/4" and JXS32 is 4"(excluding handle) **Total depth from wall tofront of closed oven doorincluding handle is 27-13/16.35-7/8"–38"from floor tocountertopIf the countertop area is not flat, excess tension may be applied to the glass cooktop causing breakageand voiding the warranty. Make sure the wall covering, countertop, flooring and cabinets around the rangecan withstand the heat (up to 200°F) generated by the range.A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or metal cabinet,or allow a 24" minimum when bottom of wood or metal cabinet is protected by no less than 1/4"-thickflame-retardant millboard covered with no less than No. 28 MSG sheet metal (.015" thick), .015"-thickstainless steel, .025" aluminum or .020" copper.B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop. However,a minimum 6" spacing to surfaces less than 15" above the cooktop and adjacent cabinetry isrecommended to reduce exposure to steam, grease splatter and heat. Allow 1/4" minimum clearanceat the back wall.To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space abovethe cooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk canbe reduced by installing a range hood that projects at least 5" beyond the front of the cabinets. Cabinetsinstalled above the cooktop must be no deeper than 13".Note: Cabinets installed adjacent to slide-in ranges must have an adhesion specof at least 194° temperature rating.Note: To reduce the possibility of scorching the side walls above the countertopwhen no load is present on burners, it is recommended that a minimum 6"spacing from adjacent side wall be allowed for possible extended high-heatelement operation.Receptacle Locations: For all 30" Slide-In Ranges locally approved flexible service cord or conduitmust be used because terminals are not accessible after range installation. See shaded areain drawing for location of electrical outlet box. Recommended outlet locations allow range to beinstalled directly against rear wall.Optional Kits For Slide-InElectric Ranges(Available At Additional Cost)Accessory Backguards(Attaches to the back of rangeas a backguard when unit isinstalled in 30" free-standingcutout)JXS32SS (Stainless) - 4" HighJXS32BB (Black) - 4" HighJXS37BB (Black) - 5-1/4" HighBody Sides(Slide-in ranges are soldwithout sides installed. Canbe installed on either leftor right when unit has oneexposed side [no cabinetadjacent]. Kit contains1 body side)JXS77BB (Black)Rear Filler StripWB07T10680 - Black Filler Strip AssemblyOptional Lower Trim Kits(If counter height is greaterthan 36.5", a lower trim kitis recommended to extendthe useful height to 38"maximum)JXS56BB – Black

/ 2

Related manuals for GE JSP39SN