GE JV535 Owner's Manual And Installation Instructions

Also see for JV535: Owner's manual and installation instructions Owner's manual and installation instructions Owner's Manual & Installation Instructions Owner's Manual & Installation Instructions Owner's manual and installation instructions

Contents

12MARK HOLESSelect the vent option that your installation will requireDQGSURFHHGWRWKDWVHFWLRQHood mounting screws (4)1315ø16” (30” hood)1615ø16” (36” hood) 1315ø16” (30” hood)1615ø16” (36” hood)Cabinet frontCenterlineElectricalaccess hole (incabinet bottom)Wood shims(recessed-bottomcabinets only)Vertical ductaccess hole101ø2”11ø4”2”12 9ø16”5”11ø4”A. Outside top exhaust(Vertical duct–31ø4” x 10” Rectangular)8VHWKHGLDJUDPRUWKHKRRGDVDWHPSODWHDQGPDUNthe locations on the cabinet for ductwork, electricalwiring and keyhole screw slots.B. 2XWVLGHWRSH[KDXVW 9HUWLFDOGXFW²” Round)8VHWKHGLDJUDPRUWKHKRRGDVDWHPSODWHDQGmark the locations on the cabinet for ductwork,electrical wiring and keyhole screw slots.Hood mounting screws (4)1315ø16” (30” hood)1615ø16” (36” hood) 1315ø16” (30” hood)1615ø16” (36” hood)Cabinet frontCenter lineElectrical access hole(in cabinet bottom)Wood shims (recessed-bottom cabinets only)AccessKROHIRU”round duct101ø2”11ø2”11ø4”121ø2”5”Cabinet bottom8” DIA.HOLECHOOSE VENTING OPTION(for JV5 Series models only)Cabinet Bottom910Wood shims (recessed-bottom cabinets only)Cabinet frontCenter lineElectrical access hole(in wall)Hood mounting screws (4)Horizontal ductaccess holeCabinetbottom1315ø16” (30” hood)1615ø16” (36” hood)1ø16”1ø8”33ø4”51ø4” 51ø4”12ø16”1315ø16” (30” hood)1615ø16” (36” hood)C. Outside rear exhaust(Horizontal duct–31ø4” x 10” Rectangular)8VHWKHGLDJUDPRUWKHKRRGDVDWHPSODWHDQGmark the locations on the cabinet for ductwork,electrical wiring and keyhole screw slots.D. Recirculating (non-vented ductless–Available on JV5 Series models only)8VHWKHKRRGDVDWHPSODWHDQGPDUNWKHORFDWLRQVon the cabinet for the electrical wiring and keyholescrew slots.6LQFHWKHKRRGLVWREHUHFLUFXODWHG QRWWREHYHQWHGoutside), do not cut out any vent openings in the wall orcabinet bottom.The hood can be set to vent outside or to recirculate airback into the kitchen.The plastic vent lever is located near the center of thehood opening. To vent to the outside, make sure the plastic ventlever is in the HORIZONTAL position (flat against themetal top of the hood). To recirculate air into the kitchen, make sure theplastic vent lever is in the VERTICAL position(flat against the plastic blower housing).NOTE: In order to change the vent lever position,you will need to pull the lever out slightly to clear theplastic tabs.51ø4”51ø4”Installation InstructionsSet foroutside ventingSet forrecirculatingStop tabHood shown lying upside downStop tab