GE Profile P2S975DEP Dimensions And Installation Information

Also see for Profile P2S975DEP: Installation instructions Owner's manual Installation instructions Owner's manual

For answers to your Monogram,® GE Profile™ orGE® appliance questions, visit our website atge.com or call GE Answer Center® service,800.626.2000.Specification Created 5/09 230141Rear filler strip or backguard are available forthese rangesNote: Door handle protrudes 3" from door face. Cabinetsand drawers on adjacent 45° and 90° walls should beplaced to avoid interference with the handle.Note: Cabinets installed adjacent to slide-inranges must have an adhesion spec of at least194° temperature rating.Optional Kits for Slide-In Gas Ranges:(Available at additional cost)Lower/Side Trim KitsJXS56BB - Lower Trim Kit (Black)Accessory BackguardsJXS32BB - Black Accessory BackguardJXS37BB - Black Glass Accessory BackguardRear Filler StripWB07T10680 - Black Filler Strip AssemblyInstallation Information: Before installing, consultinstallation instructions packed with product forcurrent dimensional data.All GE ranges are equipped withan Anti-Tip device. The installationof this device is an important,required step in the installationof the range.Dimensions and Installation Information (in inches)P2S975DEPGE Profile™ 30" Dual Fuel Slide-In Gas Range28-1/4*36Maintainat least 6"from nearestcombustiblesurface.AcceptableElectricalOutlet Area30" Slide-In RangeDimensions (in inches)45-1/82-1/4564-1/23030" Min.15" Min. 630" Slide-in Elec. RangeAug. 8, 2003 -km23-3/163030If you are NOT using theFiller strip or Backguard:If you are using theFiller strip or Backguard:25*Wall to front ofclosed door handleon model JSP34.28" on modelsJSP26/JSS26/16.Note: Range may be placed with 0" clearance (flush) at the back wall and side wallsbelow countertop if the range side trims above the countertop extend beyond the cabinetfronts at least 1/4". (Self-clean models only.) Maintain at least 6" distance from nearestcombustible surface.3031-1/228-1/4*36Maintainat least 6"from nearestcombustiblesurface.AcceptableElectricalOutlet Area30" Slide-In RangeDimensions (in inches)45-1/82-1/4564-1/23030" Min.15" Min. 630" Slide-in Elec. RangeAug. 8, 2003 -km23-3/163030If you are NOT using theFiller strip or Backguard:If you are using theFiller strip or Backguard:25*Wall to front ofclosed door handleon model JSP34.28" on modelsJSP26/JSS26/16.Note: Range may be placed with 0" clearance (flush) at the back wall and side wallsbelow countertop if the range side trims above the countertop extend beyond the cabinetfronts at least 1/4". (Self-clean models only.) Maintain at least 6" distance from nearestcombustible surface.3031-1/2Counter Cutout Dimensions (in inches)2-7/8"To FrontSurface OfCountertop20-5/8"Door ClearanceFrom FrontSurface ofCountertop31-1/430 A*AccessoryBackguard362"(Grates)24AcceptableGas Line &ElectricalOutlet AreaMax. depth ofcord, plug,receptacle box& gas hookup3-1/2" to preventinterferencewith drawer30" Min.Shave Raised Edge To Clear31-1/8 Wide Control Panel30" Min. tounprotectedcabinet fromcountertop23-3/1618" Min.13" Max.329-15/16" Min.30-1/16" Max.259/1671215*A – JXS37 is 5-1/4" and JXS32 is 4"27-1/2**44-3/4(excluding handle)**Total depth from wall tofront of closed oven doorincluding handle is 30-1/2.B is 9-1/2" from walls on either side for P2S975, PGS975and PGS908 and 6” for PGS968B35-7/8"–38"from floor tocountertop12″23-3/16″7″AcceptableGas Line &ElectricalOutlet Area30″ Min.30″ Min.fromcookingsurface to bottomof overheadcabinetsShave Raised EdgeTo Clear 31-1/8″Wide Control Panel9-1/2″Min.From Walls13″Max.depthFor OptimumInstallation TheseSurfaces MustBe Flat & LevelFollow instructionspackaged withalternate applianceCountertopDepth 25″(typical)35-3/4″to 36-1/2″from floor tocountertop18″Min. verticaldistance from thebottom of the adjacentoverhead cabinets1-1/4″Min. Counter topto top of drawerDrawercord, plug,receptacle box3.5″ to preventinterference& gas hookupMax. depth ofwith drawer9/16″29-15/16″Min.30-1/16″Max.3″15″12″23-3/16″7″AcceptableGas Line &ElectricalOutlet Area30″ Min.30″ Min.fromcookingsurface to bottomof overheadcabinetsShave Raised EdgeTo Clear 31-1/8″Wide Control Panel9-1/2″Min.From Walls13″Max.depthFor OptimumInstallation TheseSurfaces MustBe Flat & LevelFollow instructionspackaged withalternate applianceCountertopDepth 25″(typical)35-3/4″to 36-1/2″from floor tocountertop18″Min. verticaldistance from thebottom of the adjaceoverhead cabinets1-1/4″Min. Counterto top of drawerDrawercord, plug,receptacle box3.5″ to preventinterference& gas hookupMax. depth ofwith drawer9/16″29-15/16″Min.30-1/16″Max.3″15″

/ 2

Related manuals for GE Profile P2S975DEP