Garmin GPS 19x HVS Installation Instructions Manual

Also see for GPS 19x NMEA 0183: Installation instructions Installation instructions Installation instructions Installation instructions Installation instructions

Contents

Garmin GPS 19x HVS Installation Instructions Manual Manual pdf 4 page image

4connecting the Antenna to a NMeA 0183-compliant Device for two-Way communication+ ->>>>>>>>➊➎➒LO➋➏➓NM➌➐➍➑➊➋➌➍Item Description➊ GPS 19x antenna➋ 1A fuse➌ 12 Vdc battery➍ Garmin NMEA 0183-compatiblechartplotterAntennaWireColor NMEA 0183Device WireFunction➊ Red ➑ Power (+)➋ Black ➒ Ground (-)➌ Orange ➓ Accessory-ON➍ Gray L Rx A (+)➎ White/Red M Rx B (-)➏ White N Tx A (+)➐ White/Orange O Tx B (-)NMeA 0183 connection exceptions CAutIoNThe orange (Accessory-ON) wire is used whenconnecting the antenna to a Garmin chartplotter,or other NMEA 0183 device that has a definedaccessory signal wire. If you are connecting theantenna to a device that does not have an accessorysignal wire, the orange wire from the antenna shouldbe connected to ground.If you are connecting the antenna to a device thatdoes not have an accessory signal wire (Accessory-ON), connect the antenna power wire to the ignitionor install an in-line switch. The antenna will drain thebattery of the boat if it is not switched.• If your NMEA 0183-compliant device hasonly one receiving wire (Rx), connect it to thegray wire (Tx/A) from the antenna, and leavethe white/red wire (Tx/B) from the antennaunconnected.• If your NMEA 0183-compliant device has onlyone transmitting wire (Tx), connect it to the whitewire (Rx/A) from the antenna, and connect thewhite/orange wire (Rx/B) from the antenna toground.Limiting the Antenna update RateBy default, the antenna outputs position dataupdates 10 times per second using serialcommunications rate of 38400 bps. By installing theincluded resistor cable the antenna can be limited tooutput position updates once per second using serialcommunications rate of 4800 bps.1 Mount the antenna according to theseinstructions (page 1).2 If necessary, cut the cable to the appropriatelength for the installation.3 Solder the included rate-change cable in-line withthe orange Accessory-ON wire.4 Use heat-shrink tubing around the solderedconnections.5 If you have not connected the antenna already,connect the power and data cables (page 3).Chartplotter SoftwareTo ensure compatibility with the antenna, upgradeyour Garmin chartplotter with the latest software. Formore information, go to www.garmin.com/support.Care InformationThe case is constructed of high quality materials anddoes not require user maintenance, except cleaning.Cleaning the CaseClean the outer casing of the device using a clothdampened with a mild detergent solution and thenwipe dry.Avoid chemical cleaners and solvents that maydamage plastic components.SpecificationsDimensions(Diameter × Height)3 19 / 32 in. × 1 15 / 16 in.(91.6 mm × 49.5 mm)Weight 7.1 oz (201 g)Cable length 30 ft. (9.14 m)Temperature range -22° to 176°F (-30° to 80°C)Case material Fully gasketed, high-impact plasticalloy, waterproof to IEC 60529 IPX7standardsCompass-safedistance5.9 in. (150 mm)Power input source 8–33 Vdc, unregulatedInput current 40 mA at 12 VdcImportant Safety and ProductInformation WARNINGYour GPS unit may use an internal, non-user-replaceable battery for various purposes, such as thereal-time clock.Do not remove or attempt to remove the non-user-replaceable battery.When disposing of the unit, take it to a professionalservice, such as a waste electronics treatmentfacility, to have the battery removed and recycled.