Garmin GPSMAP 17 Installation Instructions Manual

Also see for GPSMAP 2006: Declaration of conformity Declaration of conformity Owner's manual Install guide Owner's manual & reference

Contents

Garmin GPSMAP 17 Installation Instructions Manual Manual pdf 5 page image

5INSTALLATION INSTRUCTIONSGPSMAP 2006C/2010C & GPS 17Flush MountTools• Flush Mount Template• Jig saw• Masking tape• Scissors• Drill• Drill bits—1/8" (3 mm) and 3/8" (6 mm)• 1/16" (2 mm) Allen (Hex) wrench• Sockets or wrenches• Hammer• Center punchTo flush mount the GPSMAP 2006C/2010C:1. Trim the Flush Mount Template and tape it in the location you want.2. Using the center punch, indent the center of each mounting hole location.3. Using an 1/8” (3 mm) drill bit, drill the four mounting holes.4. Using a 3/8” (6 mm) drill bit, drill a hole for a location to begin cutting the mounting surface.5. Using the Jig Saw, cut the mounting surface along the inside of the dashed line indicated on the template. Use a file and sandpaper torefine the size of the hole. Be very careful when cutting this hole. There is only a small amount of clearance between the casemolding and the mounting holes.6. Install the four mounting studs into unit by screwing the shorter, threaded section into the back of the unit. Use a 1/16” (2 mm) Allenwrench to tighten the mounting studs until the stop contacts the case. Be careful not to overtighten as this may damage themounting stud! The studs have a reusable thread-locking patchpre-applied from the factory.7. Place the unit in position in the cut-out of the mounting surface.8. Place washers over the mounting studs, then thread on onehex nut per mounting stud. Tighten all four until the unit is snugagainst the mounting surface. Install and tighten the second hexnut set on all four mounting studs to lock the first set in place.230mm208mmGPSMAP 2010/2010C/3010CCUT MOUNTING SURFACEALONG INSIDE OF THIS LINEUNIT OUTLINEDRILL A 3/8" HOLE.BEGIN CUTTING HERETRIM TEMPLATE ALONG THIS LINE TO AID FITTINGBe very careful when cutting this hole,there is only a small amount of clearance�between the unit and the Mounting Hole. Flush Mounting the GPS1. Trim the Flush Mount Template and tape in the desired location.2. Using the Center Punch, indent the center of each Mounting Hole location.3. Using an 1/8” (3mm) drill bit, drill the four Mounting Holes. (Drilling the mountingholes before cutting the hole for the unit will allow for an easier installation.)4. Using a 3/8” (6mm) drill bit, drill a hole for a location to begin cutting the mountingsurface.5. Using the Jig Saw, cut the mounting surface along the inside of the dashed lineindicated on the template. Be very careful when cutting this hole, there is only a smallamount of clearance between the case molding and the Mounting Holes.6. Install the four Mounting Studs into unit by screwing the shorter, threaded sectioninto the back of the unit. Use a 1/16” (2mm) Allen Wrench to tighten the Mounting Studsuntil the stop contacts the case. Be careful not to overtighten as this may damage theMounting Stud! The studs have a reusable thread-locking patch pre-applied from the factory.7. Place the unit in position in the cut out of the mounting surface.8. Place washers over the Mounting Studs, then thread on one Hex Nut per Mounting Stud.Tighten all four until the unit is snug against the mounting surface.Install and tighten the second Hex Nut on all four Mounting Studs to lock the first onein place.Flush Mount TemplateFlush MountStud Mounting surfaceWasher Hex nuts