Garmin echoMAP 70 Series Installation Instructions Manual

Also see for echoMAP 70 Series: Installation instructions Quick start manual Owner's manual Owner's manual Installation instructions

Contents

Garmin echoMAP 70 Series Installation Instructions Manual Manual pdf 3 page image

Connecting the Device to a TransducerNOTE: The device goes into simulator mode if the connection isnot secure between the device and transducer.Go to www.garmin.com or contact your local Garmin dealer todetermine the appropriate type of transducer for your needs.1 Follow the instructions provided with your transducer tocorrectly install it on your boat.2 Route the transducer cable to the back of your device, awayfrom sources of electrical interference.3 Connect the transducer cable to the appropriate port on yourdevice.Connecting the Cables to the CradleThe connectors on the cables are keyed to fit only in the correctports on the device or cradle. The connected cables are held inplace by a locking bracket.1 Remove the cable locking bracket from the cradle.2 Compare the divots À on each cable connector to the keyingon each port to determine which cable corresponds to eachport.3 Securely connect each cable to a port.4 Place the locking bracket Á over the cables and slide thebracket down to lock the cables in place.There is an audible click when the locking bracket is installedcorrectly.Installing the Device in the CradleIf your device uses a cradle and you have connected the cablesto the cradle, you can quickly place the device in the cradlewithout plugging in any cables.1 Place the base of the device in the bottom of the cradle.2 Tilt the device toward the cradle until it fastens in place.There is an audible click when the device is secured in thecradle.Removing the Device from the Cradle1 Press the release lever À on the cradle until the device isreleased.2 Tilt the device forward, and lift it out of the cradle.Updating the Device SoftwareBefore you can update the software, you must obtain asoftware-update memory card or load the latest software onto amemory card.1 Turn on the chartplotter.2 After the home screen appears, insert the memory card intothe card slot.NOTE: In order for the software update instructions toappear, the device must be fully booted before the card isinserted.3 Follow the on-screen instructions.4 Wait several minutes while the software update processcompletes.The device returns to normal operation after the softwareupdate process is complete.5 Remove the memory card.NOTE: If the memory card is removed before the devicerestarts fully, the software update is not complete.SpecificationsDevice Specification MeasurementechoMAP 70 Dimensions (W x H x D) 25 x 13.9 x 5.1 cm (9.8 x 5.5 x2 in.)Display size (W x H) 15.2 x 9.1 cm (6.0 x 3.6 in.)Weight 0.77 kg (1.7 lbs.)Power input From 10 to 18 VdcMax. power usage 20 WCompass-safe distance 65 cm (25.6 in.)echoMAP 90 Dimensions (W x H x D) 28.8 x 16.3 x 5.1 cm (11.3 x 6.4x 2 in.)Display size (W x H) 19.8 x 11.2 cm (4.4 x 7.8 in.)Weight 1 kg (2.3 lbs.)Power input From 10 to 20 VdcMax. power usage 11 WCompass-safe distance 55 cm (21.7 in.)All Models Temperature range From -15 to 55°C (from 5 to131°F)Material Polycarbonate plasticWater rating IEC 60529 IPX7Transmit power (RMS)** 500 WMaximum depth*** 701 m (2300 ft) at 77 kHzFrequencies**** • Traditional: 50, 77, or 200kHz• DownVü: 260 or 455 kHz3

/ 4

Related manuals for Garmin echoMAP 70 Series