Gemini CDJ-0I Operation Manual

Also see for CDJ-01: Operation manual

Contents

Gemini CDJ-0I Operation Manual Manual pdf 5 page image

(5)(5)(5)(5)(5)PITCH BEND BUTTONS: Pushing the PITCH BEND BUTTONS (21)will automatically raise the pitch up to +4% or lower the pitch down to-4% from the existing pitch setting. Releasing the buttons will return thepitch to the original pitch setting. You can use this function to match thepitch bend when mixing from one song to another.PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE (22)up or down will lower or raise the pitch percentage.OPERATING INSTRUCTIONS:1. Press the EJECT (7) button, place a CD in the DISC TRAY (6) and closethe tray door. The display will initially show the number of tracks and thetotal time of the CD.2. Push the TRACK SKIP (13) buttons to select the track you want to play.3. Press the PLAY/PAUSE (8) button and the unit will instantly play.CUE INSTRUCTIONS:1. To start the play at a point other than the beginning of a track, followthese instructions:First choose the track you wish to play, and then press PLAY/PAUSE (8)so the unit goes into the play mode. Press PLAY/PAUSE (8) to pauseplay at the spot where you want the play to start the CUE POINT. Usethe SEARCH BUTTONS (14) to pick the precise spot you want play tobegin, then press PLAY/PAUSE (8) again to save the cue point. Pressthe CUE (10) button to pause play at the cue point (the unit will go into thepause mode and the location indicated on the display will be thememorized cue point). You can preview the cue point by pressing andholding down CUE (10). Press PLAY/PAUSE (8) to begin play from thecue point.2. Once you have saved a cue point you can fine tune or change thememorized cue point:To change a cue point, push PLAY/PAUSE (8) so the unit plays from thecue point, then press PLAY/PAUSE (8) at the spot you wish your newcue point to be. Press PLAY/PAUSE (8) again to save the cue point. Theunit will go into the pause mode and the location indicated on the displaywill be the new memorized cue point.To fine tune a cue point, pause play at the memorized cue point, thenuse the SEARCH (14) buttons to scan frame by frame (1/75th of asecond) to where you want play to begin. Press PLAY/PAUSE (8) tosave the new cue point.NOTE: DURING FINE TUNING THERE WILL BE A STUTTER EFFECT (TO HELP YOU FIND THEBEAT). THE STUTTERING EFFECT WILL END WHEN YOU PRESS PLAY/PAUSE (8) TO SAVETHE CUE POINT. ALSO, DURING FINE TUNING IF YOU HOLD DOWN THE SEARCH (14)BUTTON, THE UNIT WILL SCAN QUICKLY AFTER 10 FRAMES.TROUBLESHOOTING:• If the disk will not play, check to see if the disc was loaded correctly(label side up). Also check the disc for excessive dirt, scratches, etc.• If the disc turns but there is no sound, check the cable connections. Ifthey are okay, check your amplifier or receiver.• If the CD skips, check the CD for dirt or scratches. Do not assume thatthe CD player is defective. Many CDs are recorded out of spec and willskip on most or all CD players. Before sending the unit in for repair, tryplaying a CD that you are sure plays properly.SPECIFICATIONS:GENERAL:Disc Type................................Standard Compact discs (12 cm & 8 cm)Time Display.....................Track Elapsed, Track Remain, or Total remainVariable Pitch......................................± 16% Slider with Resume SwitchStart...........................................................................Within 0.03 secondsTrack Selection.....................................................................1 to 99 TracksAUDIO SECTION:Quantization......................................1 Bit Linear/Channel, 3 Beam LaserOversampling Rate..........................................................................8 TimesSampling Frequency.....................................................................44.1 kHzFrequency Response......................................................20 Hz to 20 kHzTotal Harmonic Distortion..............................................Less Than 0.005%Signal to Noise Ratio.....................................................................>96 dBDynamic Range.................................................................................>94 dBOutput Level (nominal)........................................................1.9 Volts R.M.S.Power Supply.......................................................AC 120/230V, 60/50 HzDimensions...............................8.5” x 3.75” x 12.5” (216 x 95.25 x 317 mm)Weight..................................................................................4.5 lbs. (2 kg)SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGEWITHOUT NOTICE FOR PURPOSE OF IMPROVEMENT.