Gemini MX-01 Operation Manual
Contents |
INTRODUCTION:Congratulations on purchasing a MX-01 2 channel mixer fromGemini. This state of the art mixer is backed by a three yearwarranty, excluding the crossfader. The crossfader is separate-ly backed by a 90 day warranty. Prior to use we suggest that youcarefully read all the instructions.FEATURES:- 2 Stereo Channels- 2 phono & 2 line inputs- Gain Control for each channel- Cue Section- Master, Cue and Mic Volume Rotary Control- Front panel 1/4" Microphone and Headphone Jacks- Dual Ground Screws for Easy ConnectivityCAUTIONS:1. All operating instructions should be read before using thisequipment.2. To reduce the risk of electrical shock, do not open the unit.Please refer servicing to a qualified service technician.3. Do not expose this unit to direct sunlight or to a heat sourcesuch as a radiator or stove.4. This unit should be cleaned only with a damp cloth. Avoid sol-vents or other cleaning detergents.5. When moving this equipment, it should be placed in its originalcarton and packaging. This will reduce the risk of damage dur-ing transit.6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.7. DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ONANY CONTROLS OR SWITCHES.CONNECTIONS:1. Located on the rear panel is the AC IN (2) adapter jack, usedto plug in the power cord. Before plugging the adapter in, makesure the POWER SWITCH (1) located on the rear panel isturned off.2. The MX-01 has MASTER OUTPUT (3) jacks to connect to themain amplifier with RCA cables.3. Located on the rear panel are 2 PHONO (PH) RCA INPUTS(5,7), and 2 LINE (LN) RCA INPUTS (4,6). The RCA inputs forChannel (CH) 1 (16) & CH 2 (19) allow PH and LN level equip-ment to be connected to the mixer. The PH INPUTS only acceptturntables with a magnetic cartridge. When using (a)turntable(s), you will need to ground the unit(s) by screwing inthe grounding fork(s) to the DUAL GROUNDING SCREWS (8)located in the back panel of the MX-01 mixer. The stereo LNINPUTS only accept line level inputs such as a CD, DAT,MiniDisc, etc.NOTE: WHEN USING TURNTABLES, NOT ATTACHING A GROUND MAY CAUSEA SYSTEM "HUM."4. Headphones may be plugged into the face-plate located 1/4"HEADPHONE JACK (10).5. The MIC 1 (9) input (located on the front panel) is a 1/4" con-nector. The mic input accepts balanced and unbalanced micro-phones.OPERATIONS:1. Once all of your connections have been made in the rear panel,turn on the mixer by pressing the POWER SWITCH (1) and thePOWER LED will illuminate. Turn off the mixer by flipping theswitch when not in use.2. CHANNEL 1: To bring this channel into PROGRAM OUTPUT(PGM), you must first decide which line will be in use. Use theLN SWITCH (14) to toggle from PH1 (7) to LN 1 (6) on thischannel. Slowly raise the CH 1 SLIDE CONTROL (16) to a com-fortable level, once you've selected the proper line. You can fur-ther modify the sound output of this channel by adjusting therotary GAIN (15), controls located above the CH 1 SLIDE CON-TROL (16).3. CHANNEL 2: To bring this channel into PGM, you must firstdecide which line will be in use. Use the LN SWITCH (17) to tog-gle from PH2 (5) to LN2 (4) on this channel. Slowly raise the CH2 SLIDE CONTROL (19) to a comfortable level, once you'veselected the proper line. You can further modify the sound out-put of this channel by adjusting the rotary GAIN (18) controlslocated above the CH 2 SLIDE CONTROL (19).4. CUE: By connecting a set of headphones to the HEADPHONE(10) jack, you can monitor any or all channels. Use the rotaryCUE CONTROL (12) to adjust the cue volume without changingthe overall mix. By moving the CUE SWITCH (21) to the LEFTyou will be able to monitor CH 1. Moving the control to theRIGHT allows you to monitor CH 2.5. CROSSFADER SECTION: The CROSSFADER (20) allowsyou to mix from one channel to another. The CROSSFADER(20) in your unit is removable and if the need arises can be eas-ily replaced.6. OUTPUT SELECTION CONTROL: Once you are comfortablewith the sound level of your music you may adjust the volumewith the MASTER (11) rotary control.7. MIC SECTION: Plug your main mic into the MIC 1 1/4" INPUT(9) located on the front panel. The MIC 1 (9) rotary volume con-trol (13) adjust the decibel level of MIC 1 (9).SPECIFICATIONS:INPUTS:Phono...................................................................................3 mv, 47 kOhmLine...................................................................................200 mV, 22 kOhmOUTPUTS:Amp.................................................................................0 dB 1 V, 400 OhmMax..................................................................................15 V Peak to PeakGENERAL:Gain (Channels 1-2)....................................................................0 to -60 dBFrequency Response................................................20Hz - 20 kHz +/- 2 dBDistortion.............................................................................less than 0.09%S/N Ratio...........................................................................better than 60 dBHeadphone Impedance....................................................................32 OhmPower Source.................................115V/9V AC 12W (or 230V/9V AC 12W)Dimensions......................10.61 " x 3.45" x 7" (269.5 x 87.63 x 177.8 mm)Weight..............................................................................3.64 lbs. (1.65 kg)Specifications and designs are subject to change without noticefor the purpose of improvement.In the USA ~ if you experience problems withthis unit call Gemini Customer Service at: 1 (732) 738-9003. Do not attempt to return this equipment to yourdealer.REPLACEABLE CROSSFADER:1. Unscrew the outside FADER plate screws (B).- Do not touch INSIDESCREWS (C).2. Carefully remove oldCrossfader and unplug CABLE(D).3.Plug new Crossfader intoCABLE (D) and place back intomixer.4. Screw Crossfader to mixerwith the FADER PLATESCREWS (B).(44) |
Related manuals for Gemini MX-01
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine